Sharp PG-F255W quick start Resetting the Lamp Timer

Page 61

4 Remove the lamp unit.

•Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6 Replace the lamp unit cover.

•Align the tab on the lamp unit cover (1) and place it while pressing the tab

(2) to close it. Then tighten the user ser- vice screw (3) to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con- nected to the projector.

Securing screws

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex- plode.

1Connect the power cord.

•Plug the power cord into the AC socket of the projector.

2Reset the lamp timer.

•While simultaneously holding down MENU/HELP, ENTER and Ron the pro- jector, press STANDBY/ON on the pro- jector.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

STANDBY/ON button

ENTER button

R button

MENU/HELP button

Appendix

57

Image 61

Contents PG-F255W Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHOnly InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents See ÒRegarding the LampÓ onTemperature monitor function Using the projector in other countriesIf the projector starts to overheat due to setup Other connected equipmentFor Windows Setup ManualOptional accessories AccessoriesProjector Part Names and FunctionsAudio 1 input terminal Rear ViewComputer UP/PAGE COMPUTER, DVICLICK/EFFECT ButtonUsable Range Inserting the BatteriesPull down the tab on the cover and remove the cover Towards the direction of the arrowQuick Start Setup and ProjectionHeight Control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample 1610 Signal Input Normal Mode Picture Size Projection PRJ ModeProjection DistanceScreen Size and Projection Distance Signal Input Normal ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Controlling the Projector by a Computer When connecting to the LAN terminal using a LAN cable Connecting the Power CordAC socket To AC outlet Power cord supplied Turning the Projector on Turning the Projector On/OffAdjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Picture Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightHeight Adjust lever Make small adjustments Rear adjustment footPress P/Q or O/R to adjust Keystone Correction Press Keystone to enter the Keystone Correction modeCorrecting Trapezoidal Distortion Adjusting the Volume Switching the Input ModeCOMPUTER, DVI VIDEO, Video Buttons AV Mute buttonPress Resize Resize ModeResize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓImage while watching it To adjust the projected1Selecting the Picture Mode Picture Adjustment Picture MenuMenu operation n PAGE1 PAGE23Adjusting the Color Temperature 2Adjusting the Image4Adjusting the Colors Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓProgressive Lamp SettingReducing Image Noise DNR Setting the Resize Mode Adjusting the Projected Image SCR ADJ MenuAdjusting the Image Position Keystone Correction Setting the On-screen Display5Selecting the Background Image 6Selecting the Setup GuideReversing/Inverting Projected Images 8Selecting the On-screen Display Language2Auto Power Off Function 1Auto Sync Auto Sync Adjustment4STANDBY Mode 5Setting the Confirmation Sound System SoundAudio Input Fan Mode SettingSystem Lock Function This function changes the fan rotation speedEnter the same keycode in Re Checking the Lamp Life StatusConfirm Locking the Operation Buttons1Setting a Password 3TCP/IP Setting 2DHCP Client SettingEnter IP Address using P, R, Q O, then press Enter 4Confirming the Projector InformationEnter button Adjustment buttons P/R/O/Q MENU/HELP button Troubleshooting with the Help MenuUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseComputer Computer Compatibility Chart21-25 Troubleshooting52, 53 For Sharp Assistance Specifications Dimensions Index