Sharp PG-F255W quick start IntroductionENGLISH, A. only

Page 5
U.S.A. ONLY

Before using the projector, please read this operation manual carefully.

IntroductionENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1.WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2.CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection,

modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT

“LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

Introduction

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead sym- bol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

1

Image 5
Contents PG-F255W Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHOnly InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents See ÒRegarding the LampÓ onTemperature monitor function Using the projector in other countriesIf the projector starts to overheat due to setup Other connected equipmentFor Windows Setup ManualOptional accessories AccessoriesProjector Part Names and FunctionsComputer Rear ViewAudio 1 input terminal UP/PAGE COMPUTER, DVICLICK/EFFECT ButtonUsable Range Inserting the BatteriesPull down the tab on the cover and remove the cover Towards the direction of the arrowHeight Setup and ProjectionQuick Start Control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample 1610 Signal Input Normal Mode Picture Size Projection PRJ ModeProjection DistanceScreen Size and Projection Distance Signal Input Normal ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Controlling the Projector by a Computer AC socket To AC outlet Power cord supplied Connecting the Power CordWhen connecting to the LAN terminal using a LAN cable Turning the Projector on Turning the Projector On/OffAdjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Picture Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightHeight Adjust lever Make small adjustments Rear adjustment footCorrecting Trapezoidal Distortion Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Adjusting the Volume Switching the Input ModeCOMPUTER, DVI VIDEO, Video Buttons AV Mute buttonResize Resize ModePress Resize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓImage while watching it To adjust the projected1Selecting the Picture Mode Picture Adjustment Picture MenuMenu operation n PAGE1 PAGE23Adjusting the Color Temperature 2Adjusting the Image4Adjusting the Colors Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓReducing Image Noise DNR Lamp SettingProgressive Setting the Resize Mode Adjusting the Projected Image SCR ADJ MenuAdjusting the Image Position Keystone Correction Setting the On-screen Display5Selecting the Background Image 6Selecting the Setup GuideReversing/Inverting Projected Images 8Selecting the On-screen Display Language2Auto Power Off Function 1Auto Sync Auto Sync Adjustment4STANDBY Mode 5Setting the Confirmation Sound System SoundAudio Input Fan Mode SettingSystem Lock Function This function changes the fan rotation speedEnter the same keycode in Re Checking the Lamp Life StatusConfirm Locking the Operation Buttons1Setting a Password 3TCP/IP Setting 2DHCP Client SettingEnter IP Address using P, R, Q O, then press Enter 4Confirming the Projector InformationUtilizing the Help Menu Functions Troubleshooting with the Help MenuEnter button Adjustment buttons P/R/O/Q MENU/HELP button Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseComputer Computer Compatibility Chart21-25 Troubleshooting52, 53 For Sharp Assistance Specifications Dimensions Index