Sharp AR-350, AR_M280 operation manual Finisher, Supplies

Page 77

FINISHER

If the finisher is installed, the offset function can be used. Each set of printed sheets is stacked offset from the previous set so that it can be easily taken out. Also each set of sorted sheets can be stapled.

Part names

Knob

Hold this knob to open the finisher for misfeed removal.

Top cover

Open for misfeed removal.

Staple unit

Pull out to replace the staple cartridge or to remove jammed staples.

Top tray

Paper output from the printer, copier, and fax features can be delivered here.

The tray is extendable. To print onto large paper (8-1/2" x 14", 11" x 17", B4 or A3), extend the tray.

Stapler compiler Paper to be stapled is stacked temporarily.

Offset tray

The offset function and the stapling function can be used only in this tray.

NOTES

●Do not put pressure on the finisher (particularly each tray).

●Be careful about the offset tray during printing because the tray moves up and down.

●Some other peripheral units may be needed for installation of the finisher and some peripheral units cannot be installed together with the finisher. For combination of the peripheral units, see the list of combination of peripheral units on page xxxx.

Specifications

5

Name

Finisher

 

 

Number of trays

2

 

 

Exit system

Print face down

 

 

Tray type

Top tray: normal tray, Lower tray: offset tray

Paper capacity

Top tray: 500 sheets (8-1/2" x 11" or A4 size, 20 lbs. or 80 g/m2)

 

Lower tray: 750 sheets (8-1/2" x 11" or A4 size, 20 lbs. or 80 g/m2)

Paper size

Top tray: Max. 11" x 17" or A3, Min. 5-1/2" x 8-1/2"R or A5R

 

Lower tray: 8-1/2" x 11", A4 or B5R

 

 

Paper weight

Top tray: 15 to 54 lbs. or 56 to 205 g/m2

 

Lower tray: 15 to 34 lbs. or 56 to 128 g/m2

Paper type

Top tray: same as the specifications of paper for feeding in the main unit

 

Lower tray:

Paper limit detection

Provided in both the top tray and the lower tray

 

 

Offset function

Provided in the lower tray only, offset amount: 1.2 inch (30 mm)

 

 

Paper size for stapling

8-1/2" x 11", A4, and B5

 

 

Stapling capacity

30 sheets (20 lbs. or 80 g/m2)

Stapling position

Three types (one at rear, one at front, two at center)

Reference paper position

Center

 

 

Power supply

Drawn from the power supply unit (peripheral unit)(See page xx.)

 

 

Dimensions

xx-x/x” (W) x xx-x/x” (D) x xx-x/x” (H) (xxx mm (W) x xxx mm (D) x xxx mm (H))

Weight

Approx. xxx lbs. (xx kg)

 

 

Specifications are subject to change for improvement without notice.

Supplies

For the finisher, the following staple cartridge is needed as supplies.

●Staple cartridge (Approximately 3,000 staples x 3) xxxx

5-9

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Laser Printer Page Installation Requirements Battery Disposal Safety Precautions Class Laser Product Laser Klasse Line connection Facsimile FeatureFax power switch Contents Chapter Troubleshooting Maintenance Page Chapter Before Using the ProductIntroduction Duplex module IntroductionScanner module/DSPF Punch module Main Features Exterior Part Names and FunctionsInterior Part Names and FunctionsPart names and functions of peripheral units Finisher Upper exit tray extensionMail-bin stacker Stand/MPD & 2000 sheet paper drawerOther peripheral units Operation panel Job status screen To cancel the current print job and delete the print data Print key/READY indicator/DATA indicator Mode select keys and indicatorsImage Send key/LINE indicator/DATA indicator Copy key Custom Settings keyDisplay switching keys Print mode screenTouch panel Job status screen See next Print hold job listJob list Mode switching keyPaper Empty in the job status display Print JOB keyCopier feature Facsimile feature Using the touch panel How to use the touch panelExample Tone ExampleChanging the paper size in paper tray Loading PaperLoading paper in paper tray Paper available in paper trays Loading PaperPaper available in the bypass tray/multi purpose drawer Paper that can be usedMethod of setting paper size and type Press the Tray Settings key Press the Custom Settings keySelect the paper tray for which setting is To be made Touch the OK key to complete the settingHow to change the paper size SpecificationsSetting envelopes or postcards Loading paper in the multi purpose drawerMiddle and lower paper trays Loading paper in the stand/3 x 500 sheet paper drawerUpper paper tray Upper paper tray Loading paper in the stand/MPD & 2000 sheet paper drawerPull out the large capacity tray Gently push the large capacity paper tray Into the printerProper storage Adding TonerStorage of Supplies Page Printing from a Computer Using this machine as a local printer Connecting to a ComputerUsing this machine as a network printer Software for WindowsClick the Start button Uninstalling Printer UtilitiesOn the Start menu, select Settings Then Printers Before installationClick the Have Disk button Computer type Operating systemRight-click the installed printer driver Select Properties Setting the Printer DriverWindows 95 / 98 / Me Set each itemAccessing Web pages and displaying help Environment required for accessing Web pagesClick the Help button under the menu Frame Close the helpItems and outline of menu frame of Web pages Remote Operation Through NetworkSet up Hold before print PasswordNormal print Use the same procedure as to enter Enter the fifth digit of the password Press the OK keyPrinting method of hold job list Press the Menu keyOperation is now complete Enter the passwordEnsure that the desired number of copies Is set Printer account control Printer Basic Settings Making Configuration Setting Touch the key of the desired item to display Making Configuration SettingTo finish the setting operation, touch Exit key PostScript settings Main program settingsPCL settings Press the Menu key to display Custom settings menu screen Custom SettingsIts setting screen Custom SettingsPress the Custom Settings key when Setting items Page Troubleshooting and Maintenance General misfeed removal procedure When using the operation panel on the main unitMisfeed Removal Press the Information key to close Misfeed removal guidanceMisfeed removal guidance When using the operation panel with touch panelMisfeed in paper tray Misfeed in the paper feed areaMisfeed in the stand/3 x 500 sheet paper Drawer Misfeed in the multi purpose drawerMisfeed in the stand/MPD & 2000 sheet paper drawer Misfeed in the transport area, fusing area, and exit area Misfeed in the bypass tray Misfeed in the duplex moduleProblem Solution TroubleshootingTroubleshooting Troubleshooting Supplementary explanation for printing Cleaning the scanner module User MaintenancePeripheral Units Part names Duplex ModuleOpen the bypass tray Duplex ModuleSet the type of the loaded paper Loading paper in the bypass tray is now CompleteSetting copy functions in accordance with your purpose Setting the printer driver in accordance with your purposeSee Troubleshooting concerning the duplex moduleMAIL-BIN Stacker Using the mail-bin stacker Setting in the printer driverMAIL-BIN Stacker Specifying a mail binClose the paper guide Misfeed in the mail-bin stackerOpen the top cover Supplies FinisherOffset mode Sort mode Group modeStaple sort mode FinisherUsing the finisher functions in the copy mode Using the finisher functionsUsing the stapling function from the printer feature Open the front cover Turn the staple unit to face up Staple cartridge replacement and staple jam removalBox Remove the empty staple cartridgeFinisher Remove the misfed paper from the stapler Compiler Misfeed in the finisherOpen the paper guide and remove Misfed paper Close the finisher Remove the misfed paperNot operate Troubleshooting concerning the finisherStapling position quick reference list Part names SpecificationsSaddle Stitch Finisher Saddle Stitch Finisher Saddle stitch finisher functionsStaple sort mode Using the finisher functions in the copy mode Using the saddle stitch finisher functionsInsert a new staple cartridge into the staple 6box Staple cartridge replacement and staple jam removalStaple cartridge replacement 10Close the front cover 8Insert the staple box9Push back the stapler section 1Open the front cover9Remove the staple box Punch scrap disposal11Return the lever to its original position 12Insert the staple boxPull the knob and slide the saddle stitch Misfeed in the saddle stitch finisher5Remove the misfed paper BelowTurn roller rotating knob D in the direction 13of the arrow 11Remove the misfed paperTurn roller rotating knob D in the direction 12of the arrow Troubleshooting concerning the saddle stitch finisher Binding Stapling position quick reference listRelation between print image and saddle stitch KEY Operator Programs Key operator proguram list KEY Operator ProgramsKEY Operator Programs Using the key operator programsBACK/C Restore Configuration 5Press the Custom Settings key Use the numeric keys to enter the five-digit 3password6Press the Custom Settings key 2Touch the KEY Operator Programs keyDescription of setting programs Auto power shut-off Energy save Auto power shut-off timerPreheat mode Toner save Toner save in printer modeBeep setting Operation panel settings Auto clear settingLanguage setting Disabling of job priority operationDisable duplex unit Device settingsDisable stapler unit Disable paper desk drawersDisable notice page printing System settings default settingsDisable test page printing Print density levelHexadecimal dump mode System settings Interface settingsPDL for network port Network port emulation switching TimeoutReset the NIC System settings network settingsIP address setting EnableTCP/IPRestore factory defaults System settings initialize/store settingsStore current configuration Restore configurationAppendix CPU Printer SpecificationsList of principal printer functions List of Combination of Peripheral Units Disabling notice page and separator sheet printing Case of portrait orientation in mm Print Area
Top Page Image Contents