Sharp AR-350, AR_M280 operation manual Installation Requirements

Page 3

INSTALLATION REQUIREMENTS

Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.

1. The machine should be installed near an accessible power outlet for easy connection.

2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.

● For the power supply requirements, see the name plate of the main unit.

3. Do not install your machine in areas that are: ● damp, humid, or very dusty

● exposed to direct sunlight

●poorly ventilated

●subject to extreme temperature or humidity

changes, e.g., near an air conditioner or heater.

4. Be sure to allow the required space around the machine for servicing and proper ventilation.

11-13/16" (30cm)

A small amount of ozone is produced within the copier

23-5/8" (60cm)

23-5/8" (60cm)

23-5/8" (60cm)

during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

0-1

Image 3

Contents Laser Printer Page Installation Requirements Battery Disposal Safety Precautions Class Laser Product Laser Klasse Facsimile Feature Fax power switchLine connection Contents Chapter Troubleshooting Maintenance Page Chapter Before Using the ProductIntroduction Introduction Scanner module/DSPFDuplex module Punch module Main Features Exterior Part Names and FunctionsInterior Part Names and FunctionsPart names and functions of peripheral units Stand/MPD & 2000 sheet paper drawer Upper exit tray extensionFinisher Mail-bin stackerOther peripheral units Operation panel Job status screen To cancel the current print job and delete the print data Custom Settings key Mode select keys and indicatorsPrint key/READY indicator/DATA indicator Image Send key/LINE indicator/DATA indicator Copy keyJob status screen See next Print hold job list Print mode screenDisplay switching keys Touch panelPrint JOB key Mode switching keyJob list Paper Empty in the job status displayTone Example Using the touch panel How to use the touch panelCopier feature Facsimile feature ExampleLoading Paper Loading paper in paper trayChanging the paper size in paper tray Paper that can be used Loading PaperPaper available in paper trays Paper available in the bypass tray/multi purpose drawerMethod of setting paper size and type Touch the OK key to complete the setting Press the Custom Settings keyPress the Tray Settings key Select the paper tray for which setting is To be madeLoading paper in the multi purpose drawer SpecificationsHow to change the paper size Setting envelopes or postcardsLoading paper in the stand/3 x 500 sheet paper drawer Upper paper trayMiddle and lower paper trays Gently push the large capacity paper tray Into the printer Loading paper in the stand/MPD & 2000 sheet paper drawerUpper paper tray Pull out the large capacity trayAdding Toner Storage of SuppliesProper storage Page Printing from a Computer Software for Windows Connecting to a ComputerUsing this machine as a local printer Using this machine as a network printerClick the Start button Uninstalling Printer UtilitiesComputer type Operating system Before installationOn the Start menu, select Settings Then Printers Click the Have Disk buttonSet each item Setting the Printer DriverRight-click the installed printer driver Select Properties Windows 95 / 98 / MeClose the help Environment required for accessing Web pagesAccessing Web pages and displaying help Click the Help button under the menu FrameItems and outline of menu frame of Web pages Remote Operation Through NetworkSet up Password Normal printHold before print Press the Menu key Enter the fifth digit of the password Press the OK keyUse the same procedure as to enter Printing method of hold job listEnter the password Ensure that the desired number of copies Is setOperation is now complete Printer account control Printer Basic Settings Making Configuration Setting Making Configuration Setting To finish the setting operation, touch Exit keyTouch the key of the desired item to display Main program settings PCL settingsPostScript settings Press the Menu key to display Custom settings menu screen Custom SettingsCustom Settings Press the Custom Settings key whenIts setting screen Setting items Page Troubleshooting and Maintenance Press the Information key to close Misfeed removal guidance When using the operation panel on the main unitGeneral misfeed removal procedure Misfeed RemovalMisfeed removal guidance When using the operation panel with touch panelMisfeed in paper tray Misfeed in the paper feed areaMisfeed in the multi purpose drawer Misfeed in the stand/MPD & 2000 sheet paper drawerMisfeed in the stand/3 x 500 sheet paper Drawer Misfeed in the transport area, fusing area, and exit area Misfeed in the bypass tray Misfeed in the duplex moduleProblem Solution TroubleshootingTroubleshooting Troubleshooting Supplementary explanation for printing Cleaning the scanner module User MaintenancePeripheral Units Part names Duplex ModuleLoading paper in the bypass tray is now Complete Duplex ModuleOpen the bypass tray Set the type of the loaded paperSetting copy functions in accordance with your purpose Setting the printer driver in accordance with your purposeSee Troubleshooting concerning the duplex moduleMAIL-BIN Stacker Specifying a mail bin Setting in the printer driverUsing the mail-bin stacker MAIL-BIN StackerMisfeed in the mail-bin stacker Open the top coverClose the paper guide Supplies FinisherFinisher Sort mode Group modeOffset mode Staple sort modeUsing the finisher functions Using the stapling function from the printer featureUsing the finisher functions in the copy mode Remove the empty staple cartridge Staple cartridge replacement and staple jam removalOpen the front cover Turn the staple unit to face up BoxFinisher Close the finisher Remove the misfed paper Misfeed in the finisherRemove the misfed paper from the stapler Compiler Open the paper guide and remove Misfed paperNot operate Troubleshooting concerning the finisherStapling position quick reference list Specifications Saddle Stitch FinisherPart names Saddle Stitch Finisher Saddle stitch finisher functionsStaple sort mode Using the finisher functions in the copy mode Using the saddle stitch finisher functionsStaple cartridge replacement and staple jam removal Staple cartridge replacementInsert a new staple cartridge into the staple 6box 1Open the front cover 8Insert the staple box10Close the front cover 9Push back the stapler section12Insert the staple box Punch scrap disposal9Remove the staple box 11Return the lever to its original positionBelow Misfeed in the saddle stitch finisherPull the knob and slide the saddle stitch 5Remove the misfed paper11Remove the misfed paper Turn roller rotating knob D in the direction 12of the arrowTurn roller rotating knob D in the direction 13of the arrow Troubleshooting concerning the saddle stitch finisher Binding Stapling position quick reference listRelation between print image and saddle stitch KEY Operator Programs Key operator proguram list KEY Operator ProgramsKEY Operator Programs Using the key operator programsBACK/C Restore Configuration 2Touch the KEY Operator Programs key Use the numeric keys to enter the five-digit 3password5Press the Custom Settings key 6Press the Custom Settings keyDescription of setting programs Toner save Toner save in printer mode Energy save Auto power shut-off timerAuto power shut-off Preheat modeDisabling of job priority operation Operation panel settings Auto clear settingBeep setting Language settingDisable paper desk drawers Device settingsDisable duplex unit Disable stapler unitPrint density level System settings default settingsDisable notice page printing Disable test page printingTimeout System settings Interface settingsHexadecimal dump mode PDL for network port Network port emulation switchingEnableTCP/IP System settings network settingsReset the NIC IP address settingRestore configuration System settings initialize/store settingsRestore factory defaults Store current configurationAppendix CPU Printer SpecificationsList of principal printer functions List of Combination of Peripheral Units Disabling notice page and separator sheet printing Case of portrait orientation in mm Print Area