Loading paper in the bypass tray

Sharp AR-M276 Loading paper in the bypass tray, Set the paper guides to the copy paper width

Page 20

BEFORE USING THE MACHINE

1 Unfold the bypass tray.	3 Insert the copy paper (print side
	down) all the way into the bypass tray.

To enable correct detection of the paper size, be sure to pull out the bypass tray extension.

2 Set the paper guides to the copy paper width.

Important points when inserting paper in the bypass tray

•Be sure to place envelopes horizontally as shown in the following diagram.

•Load the paper with the print side facing down.

Landscape Portrait orientation orientation

•When loading envelopes, make sure that they are straight and flat and do not have loosely glued construction flaps (not the closure flap).

•When adding paper, first remove any paper remaining in the bypass tray, combine it with the paper to be added, and then reload as a single stack. The paper to be added must be the same size and type as the paper already in the bypass tray.

•Do not use paper that is smaller than the original image. This may cause smudges or unclean images.

•Do not use paper that has already been printed on by a laser printer or plain paper fax machine. This may cause smudges or unclean images.

Image 20

Contents

AR-M236 AR-M276 Page Contents When a finisher AR-FN5N is installed 500-SHEET Paper Feed UnitImportant Points When Selecting AN Installation Site Do not install your machine in areas that areChanges, e.g., near an Air conditioner orTrademark acknowledgements Do not touch the photoconductive drum green portionUsing the Manual Software setup guide for printerEnvironmental Information Online manual for printerMeaning of R in Original and Paper Size Indications Conventions Used in this ManualExplanation of words and illustration AB series metric and inch series referencesMain Features Part Names and Functions Interior Operation Panel Using the touch panel Selecting a function Touch PanelExample Beep toneMode switching keys Display switching keysJob list Print JOB keyPower on and OFF Power onPower OFF Turn the power switch to the on positionInitial Settings Power Save ModesPreheat mode Auto power shut-off mode Tray Paper tray type Paper type Size Weight Capacity Loading Paper Paper Upper paper tray*1 Plain paper A5 to A3 56 g/m2 to 105 g/m2Follow these guidelines when using special papers Special papersEnvelopes Letterhead paperLoading Paper Loading the paper in the paper traySet the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading paper in the bypass tray Select the tray in which you loaded paper Changing a TRAY’S Paper Type and Paper Size SettingsTouch the Tray Settings key Setting the paper type in the bypass tray Main Screen of Copy Mode How to place the original Normal CopyingCopying from the Document Glass Close the document cover/RSPFAdjust the original guides to the size of the original Stream feeding modeCopying from the Rspf Copying a large number of originalsPoints to Note When Making Copies Document glass and RspfOriginals that can be used in the Rspf Removing the document coverSelect the MIX Size Original Feeding Mode checkbox Copying originals of mixed length Mixed feedingAutomatic copy image rotation rotation copying Touch the Special Modes keyShifting the starting position of copying Set the type of paper thatYou loaded in the bypass Tray. p.20Using the Document Glass Automatic TWO-SIDED CopyingTouch the One-sided to two-sided copy key Original → PaperUsing the Rspf Touch the desired copy modeTo cancel automatic two-sided copying, press the Clear key Original for the front side is scannedExposure Adjustment Touch the Exposure key Manually adjust the copy exposureSelecting the original image type Exposure value guidelinesOriginal type setting Original position Selectable ratios REDUCTION/ENLARGEMENT/ZOOMAutomatic Ratio Selection Place the originals. p.22, p.23Manual Ratio Selection Place the originals. p.22, p.23 Touch the Copy Ratio keyTouch the XY Zoom key Copy ratio in the vertical Y direction Zoom keys To changeCopy ratio in the horizontal DirectionReplace only the originals that have not yet been scanned Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Copy Finishing Functions Sort CopyGroup Copy Offset FunctionWhen using the Rspf When using the document glassTouch the Output key Touch the Sort or Group keyUsing the Rspf Using the document glass Staple SortOrientation of the Original and Stapling Positions Insert the originals face up Place each original face downPlace the originals. p.22, p.23 Touch the Output key Touch the Staple Sort keySpecial Modes Example Selecting the margin shift function General Procedure for Using the Special FunctionsTouch the key of the desired special mode Adjust the shift width as needed and touch the OK key Margin Shift CopyTouch the Margin Shift key in the special modes screen Select the shift directionSelect the desired erase mode Adjust the erase width as needed and touch the OK keyErase Copy Touch the Erase key in the special modes screenWhen copying book originals Dual page CopyTouch the Dual page Copy key in the special modes screen Place the originals on the document glass. p.22Pamphlet Copy Specify whether 1-sided or 2-sided originals will be copiedTouch the READ-END key JOB Build ModeTouch the JOB Build key in the special modes menu screen Multi Shot Copy Original Size Touch the Manual keySelect the original size Touch the inside OK keyNot copying onto a cover Cover CopyCopying onto a cover Touch the OK key in the cover setting screen Select the covers that you wish to addLoad the cover paper to be used into the bypass tray Specify whether or not the front cover is to be copied onCustom Settings This is used to print a setting list or a font list. p.52Continuous printing. p.52 ProgrammedGeneral Procedure for Custom Settings Custom SettingsSettings Touch the STORE/DELETE key JOB Program MemoryStoring a JOB Program Executing a JOB Program Deleting a Stored JOB ProgramPress the key Touch the program number key of the desired programAuditing Mode Copying When Auditing Mode is EnabledWhen the copy job is finished, press the ACC.#-C key Enter your account number 5 digits with the numeric keysImage quality problems Trouble Problems related to machine operationPaper feeding problems Message Cause and solution Display MessagesContact your authorised service representative Staples are jammed in the finisher or the staple case is notTroubleshooting Problems related to machine operationAutomatically, or copying does not Original is not a standard sizeCopy, print job, or received fax is being printed Originals were being scannedPaper feeding problems Image quality problems First, locate the misfeed Misfeed RemovalMisfeed Removal Guidance Misfeed in the Rspf Remove the misfed originalSection C Section aMisfeed in the paper feed area Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the fusing area Close the front cover and side coverTurn the roller rotating knob in the direction of the arrow Make sure that the misfeed message is clearedReplace the upper paper tray Misfeed in the Centre TrayMisfeed in the Upper Paper Tray Misfeed in the Lower Paper Tray Open the lower side cover Remove the misfed paperReplace the lower paper tray Close the lower side coverGently pull the misfed paper out Misfeed in the Upper Exit AreaMisfeed in AN Output Tray Troubleshooting and Maintenance Replacing the Toner Cartridge Close the front coverStaple Cartridge Replacement Checking the total output count and toner quantity Checking the Toner Quantity and Total Output CountStaple JAM Removal Cleaning the Machine Document Glass and Document COVER/RSPFBypass Tray Paper Feed Roller Surface of document glass Underside of document cover/RSPFPeripheral Devices Reversing Single Pass Feeder AR-RP7 SeePart names SpecificationsFinisher AR-FN5N Capacity Lower tray Sheet Paper Feed UnitPaper Upper tray Storage of Supplies Reversing Single Pass FeederProper Storage Store the supplies in a location that isSpecifications Resolution Power consumptionOverall dimensions Developer systemProduct Name Supplier Identification Sharp CorporationPersonal Precautions Environmental PrecautionsMethods for Cleaning Up Most Important Hazards and Effects of the ProductsExposure limit values Personal Protective EquipmentAppearance Boiling/Melting PointHuman exposures 4/4Chronic Effect Data Issued Aug Msds No. F-31201AR-271ND / AR-271DV / AR-271SD / AR-271SD-C Black Developer Ingredient CAS No ProportionData Issued Aug Msds No. F-31201 Toxicological Information Acute ToxicityDisposal Considerations Symbols IndexHow to place the original Important points when inserting paperImportant points when selecting an installation site Job programPoints to note when making copies Power save modesSetting the paper type in the bypass tray 15, 19Using convenient copy functions Troubleshooting and maintenancePreparations Making copiesMemo Memo Memo Class Laser Product Laser Klasse Mains Plug Wiring Instructions 2003H KS ➀

Related manuals

Sharp AR-M276 Loading paper in the bypass tray, Set the paper guides to the copy paper width