Select the covers that you wish to add

Sharp AR-M236, AR-M276 operation manual Select the covers that you wish to add

Page 51

CONVENIENT COPY FUNCTIONS

1 Touch the key and then touch the [COVER] key in the special modes menu screen.

		The cover setting screen
	L	will appear.
	L	The cover icon ( , etc.)
	COVER	The cover icon ( , etc.)
		will also appear in the
		screen to indicate that
		the function is turned on.

2 Select the cover(s) that you wish to add.

SPECIAL MODES

CANCEL

COVER

FRONT

BACK

FRONT+BACK

PRINT ON FRONT COVER?

YES

To add only a front cover, touch the [FRONT] key. To add only a back cover, touch the [BACK] key. To add both a front and back cover, touch the [FRONT+BACK] key.

6 Load the cover paper to be used into the bypass tray.

Load the same size of paper as the paper to be used for the copy job.

About the steps that follow

See page 23.

•	It is not possible to copy on the inside of a
Note	front cover, nor on either side of a back
	cover.
•	Be sure to place the originals in the RSPF.
	The document glass cannot be used for this
	function.	3
• During cover copying, stream feeding mode
	will not function even if enabled in the key
	operator programs. (See the "Key
	operator’s guide".)
•	To cancel the cover copy function, select
	the cover copy function again and touch the
	[CANCEL] key. (See the screen of step 2.)

Specify whether or not the front cover is to be copied on.

		CANCEL		OK	Select [YES] or [NO] in
					Select [YES] or [NO] in
					the touch panel. If
PRINT ON FRONT COVER?					the touch panel. If
					[YES] is selected, the
	YES		NO		[YES] is selected, the

first page of the document will be copied onto the front cover sheet.

4 Touch the [OK] key in the cover setting screen.

Return to the special modes screen.

5 Touch the [OK] key in the special modes screen.

You will return to the main screen of copy mode.

Image 51

Contents

AR-M236 AR-M276 Page Contents 500-SHEET Paper Feed Unit When a finisher AR-FN5N is installedAir conditioner or Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Changes, e.g., near anDo not touch the photoconductive drum green portion Trademark acknowledgementsOnline manual for printer Using the ManualSoftware setup guide for printer Environmental InformationAB series metric and inch series references Meaning of R in Original and Paper Size IndicationsConventions Used in this Manual Explanation of words and illustrationMain Features Part Names and Functions Interior Operation Panel Beep tone Using the touch panel Selecting a functionTouch Panel ExamplePrint JOB key Mode switching keysDisplay switching keys Job listTurn the power switch to the on position Power on and OFFPower on Power OFFAuto power shut-off mode Initial SettingsPower Save Modes Preheat modeUpper paper tray*1 Plain paper A5 to A3 56 g/m2 to 105 g/m2 Tray Paper tray type Paper type Size Weight CapacityLoading Paper PaperLetterhead paper Follow these guidelines when using special papersSpecial papers EnvelopesLoading the paper in the paper tray Loading PaperImportant points when inserting paper in the bypass tray Loading paper in the bypass traySet the paper guides to the copy paper width Changing a TRAY’S Paper Type and Paper Size Settings Touch the Tray Settings keySelect the tray in which you loaded paper Setting the paper type in the bypass tray Main Screen of Copy Mode Close the document cover/RSPF How to place the originalNormal Copying Copying from the Document GlassCopying a large number of originals Adjust the original guides to the size of the originalStream feeding mode Copying from the RspfRemoving the document cover Points to Note When Making CopiesDocument glass and Rspf Originals that can be used in the RspfTouch the Special Modes key Select the MIX Size Original Feeding Mode checkboxCopying originals of mixed length Mixed feeding Automatic copy image rotation rotation copyingTray. p.20 Shifting the starting position of copyingSet the type of paper that You loaded in the bypassOriginal → Paper Using the Document GlassAutomatic TWO-SIDED Copying Touch the One-sided to two-sided copy keyOriginal for the front side is scanned Using the RspfTouch the desired copy mode To cancel automatic two-sided copying, press the Clear keyExposure value guidelines Exposure AdjustmentTouch the Exposure key Manually adjust the copy exposure Selecting the original image typePlace the originals. p.22, p.23 Original type setting Original position Selectable ratiosREDUCTION/ENLARGEMENT/ZOOM Automatic Ratio SelectionPlace the originals. p.22, p.23 Touch the Copy Ratio key Manual Ratio SelectionTouch the XY Zoom key Direction Copy ratio in the vertical Y directionZoom keys To change Copy ratio in the horizontalInterrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace only the originals that have not yet been scanned Offset Function Copy Finishing FunctionsSort Copy Group CopyTouch the Sort or Group key When using the RspfWhen using the document glass Touch the Output keyInsert the originals face up Place each original face down Using the Rspf Using the document glassStaple Sort Orientation of the Original and Stapling PositionsTouch the Staple Sort key Place the originals. p.22, p.23 Touch the Output keySpecial Modes General Procedure for Using the Special Functions Touch the key of the desired special modeExample Selecting the margin shift function Select the shift direction Adjust the shift width as needed and touch the OK keyMargin Shift Copy Touch the Margin Shift key in the special modes screenTouch the Erase key in the special modes screen Select the desired erase modeAdjust the erase width as needed and touch the OK key Erase CopyPlace the originals on the document glass. p.22 When copying book originalsDual page Copy Touch the Dual page Copy key in the special modes screenSpecify whether 1-sided or 2-sided originals will be copied Pamphlet CopyJOB Build Mode Touch the JOB Build key in the special modes menu screenTouch the READ-END key Multi Shot Copy Touch the inside OK key Original SizeTouch the Manual key Select the original sizeCover Copy Copying onto a coverNot copying onto a cover Specify whether or not the front cover is to be copied on Touch the OK key in the cover setting screenSelect the covers that you wish to add Load the cover paper to be used into the bypass trayProgrammed Custom SettingsThis is used to print a setting list or a font list. p.52 Continuous printing. p.52Custom Settings General Procedure for Custom SettingsSettings JOB Program Memory Storing a JOB ProgramTouch the STORE/DELETE key Touch the program number key of the desired program Executing a JOB ProgramDeleting a Stored JOB Program Press the keyEnter your account number 5 digits with the numeric keys Auditing ModeCopying When Auditing Mode is Enabled When the copy job is finished, press the ACC.#-C keyTrouble Problems related to machine operation Paper feeding problemsImage quality problems Display Messages Message Cause and solutionStaples are jammed in the finisher or the staple case is not Contact your authorised service representativeProblems related to machine operation TroubleshootingOriginals were being scanned Automatically, or copying does notOriginal is not a standard size Copy, print job, or received fax is being printedPaper feeding problems Image quality problems Misfeed Removal Misfeed Removal GuidanceFirst, locate the misfeed Section a Misfeed in the RspfRemove the misfed original Section CMisfeed in the Bypass Tray Misfeed in the MachineMisfeed in the paper feed area Make sure that the misfeed message is cleared Misfeed in the fusing areaClose the front cover and side cover Turn the roller rotating knob in the direction of the arrowMisfeed in the Centre Tray Misfeed in the Upper Paper TrayReplace the upper paper tray Close the lower side cover Misfeed in the Lower Paper TrayOpen the lower side cover Remove the misfed paper Replace the lower paper trayMisfeed in the Upper Exit Area Misfeed in AN Output TrayGently pull the misfed paper out Troubleshooting and Maintenance Close the front cover Replacing the Toner CartridgeStaple Cartridge Replacement Checking the Toner Quantity and Total Output Count Staple JAM RemovalChecking the total output count and toner quantity Surface of document glass Underside of document cover/RSPF Cleaning the MachineDocument Glass and Document COVER/RSPF Bypass Tray Paper Feed RollerReversing Single Pass Feeder AR-RP7 See Peripheral DevicesSpecifications Finisher AR-FN5NPart names Sheet Paper Feed Unit Paper Upper trayCapacity Lower tray Store the supplies in a location that is Storage of SuppliesReversing Single Pass Feeder Proper StorageSpecifications Developer system ResolutionPower consumption Overall dimensionsSupplier Identification Sharp Corporation Product NameMost Important Hazards and Effects of the Products Personal PrecautionsEnvironmental Precautions Methods for Cleaning UpBoiling/Melting Point Exposure limit valuesPersonal Protective Equipment Appearance4/4 Chronic EffectHuman exposures Ingredient CAS No Proportion Data Issued AugMsds No. F-31201 AR-271ND / AR-271DV / AR-271SD / AR-271SD-C Black DeveloperData Issued Aug Msds No. F-31201 Acute Toxicity Toxicological InformationDisposal Considerations Index SymbolsJob program How to place the originalImportant points when inserting paper Important points when selecting an installation site15, 19 Points to note when making copiesPower save modes Setting the paper type in the bypass trayMaking copies Using convenient copy functionsTroubleshooting and maintenance PreparationsMemo Memo Memo Class Laser Product Laser Klasse Mains Plug Wiring Instructions 2003H KS ➀

Related manuals

Sharp AR-M236, AR-M276 operation manual Select the covers that you wish to add