Automatic TWO-SIDED Copying, Original → Paper

Sharp AR-M236, AR-M276 Automatic TWO-SIDED Copying, Using the Document Glass, Original → Paper

Page 29

AUTOMATIC TWO-SIDED COPYING

Two originals can be automatically copied onto both sides of a single sheet of paper. When the RSPF is used, two-sided copies of two-sided originals can easily be made.

Original → Paper

One-sided original → Two sides ( )

Document glass

One-sided original

Two-sided original

→ Two sides

→ One side

(

)

(

)

(

)

RSPF

Note

• Paper sizes that can be used are A5, B5, B5R, A4, A4R, B4, and A3 (8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13",

8-1/2" x 14" and 11" x 17").

•When making two-sided copies on letterhead paper, place the side with the letterhead face down if using a tray, or face up if using the bypass tray (This is the opposite of normal.).

•Automatic two-sided copying is not possible on thick paper, thin paper, labels, transparency film, envelopes, and other special types of paper.

•If automatic two-sided copying is performed using super photo mode, the memory may become full ("MEMORY IS FULL, SELECT ANOTHER EXPOSURE MODE." will appear.). Touch the [OK] key to cancel automatic two-sided copying, set the exposure setting to other than super photo mode, and select automatic two-sided copying once again.

•Automatic two-sided copying can be disabled in the key operator programs. (See the "Key operator’s guide".)

•When dual page copy (p.43) is selected, two-sided original to two sides or two-sided original to one side cannot be used.

USING THE DOCUMENT GLASS

1 Place the original on the document glass. (p.22)

2 Touch the [2-SIDED COPY] key.

2-SIDED COPY

OUTPUT

3 Touch the [One-sided to two-sided copy] key.

Touch the [BINDING CHANGE] key when making the tablet binding, or when making automatic two-sided copies of a one-sided A3 (11" x 17") or B4 (8-1/2" x 14") size portrait original, touch the [BINDING CHANGE] key.

Portrait-oriented original

(A3 or B4 (11" x 17" or 8-1/2" x 14") size)

Before [BINDING CHANGE] After [BINDING CHANGE]

4 Touch the [OK] key.

BINDING

CHANGE

Image 29

Contents

AR-M236 AR-M276 Page Contents 500-SHEET Paper Feed Unit When a finisher AR-FN5N is installedDo not install your machine in areas that are Important Points When Selecting AN Installation SiteChanges, e.g., near an Air conditioner orDo not touch the photoconductive drum green portion Trademark acknowledgementsSoftware setup guide for printer Using the ManualEnvironmental Information Online manual for printerConventions Used in this Manual Meaning of R in Original and Paper Size IndicationsExplanation of words and illustration AB series metric and inch series referencesMain Features Part Names and Functions Interior Operation Panel Touch Panel Using the touch panel Selecting a functionExample Beep toneDisplay switching keys Mode switching keysJob list Print JOB keyPower on Power on and OFFPower OFF Turn the power switch to the on positionPower Save Modes Initial SettingsPreheat mode Auto power shut-off modeLoading Paper Tray Paper tray type Paper type Size Weight CapacityPaper Upper paper tray*1 Plain paper A5 to A3 56 g/m2 to 105 g/m2Special papers Follow these guidelines when using special papersEnvelopes Letterhead paperLoading the paper in the paper tray Loading PaperSet the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading paper in the bypass tray Select the tray in which you loaded paper Changing a TRAY’S Paper Type and Paper Size SettingsTouch the Tray Settings key Setting the paper type in the bypass tray Main Screen of Copy Mode Normal Copying How to place the originalCopying from the Document Glass Close the document cover/RSPFStream feeding mode Adjust the original guides to the size of the originalCopying from the Rspf Copying a large number of originals Document glass and Rspf Points to Note When Making Copies Originals that can be used in the Rspf Removing the document coverCopying originals of mixed length Mixed feeding Select the MIX Size Original Feeding Mode checkboxAutomatic copy image rotation rotation copying Touch the Special Modes keySet the type of paper that Shifting the starting position of copyingYou loaded in the bypass Tray. p.20Automatic TWO-SIDED Copying Using the Document GlassTouch the One-sided to two-sided copy key Original → PaperTouch the desired copy mode Using the RspfTo cancel automatic two-sided copying, press the Clear key Original for the front side is scannedTouch the Exposure key Manually adjust the copy exposure Exposure AdjustmentSelecting the original image type Exposure value guidelinesREDUCTION/ENLARGEMENT/ZOOM Original type setting Original position Selectable ratiosAutomatic Ratio Selection Place the originals. p.22, p.23Place the originals. p.22, p.23 Touch the Copy Ratio key Manual Ratio SelectionTouch the XY Zoom key Zoom keys To change Copy ratio in the vertical Y directionCopy ratio in the horizontal DirectionReplace only the originals that have not yet been scanned Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Sort Copy Copy Finishing FunctionsGroup Copy Offset FunctionWhen using the document glass When using the RspfTouch the Output key Touch the Sort or Group keyStaple Sort Using the Rspf Using the document glassOrientation of the Original and Stapling Positions Insert the originals face up Place each original face downTouch the Staple Sort key Place the originals. p.22, p.23 Touch the Output keySpecial Modes Example Selecting the margin shift function General Procedure for Using the Special FunctionsTouch the key of the desired special mode Margin Shift Copy Adjust the shift width as needed and touch the OK keyTouch the Margin Shift key in the special modes screen Select the shift directionAdjust the erase width as needed and touch the OK key Select the desired erase modeErase Copy Touch the Erase key in the special modes screenDual page Copy When copying book originalsTouch the Dual page Copy key in the special modes screen Place the originals on the document glass. p.22Specify whether 1-sided or 2-sided originals will be copied Pamphlet CopyTouch the READ-END key JOB Build ModeTouch the JOB Build key in the special modes menu screen Multi Shot Copy Touch the Manual key Original SizeSelect the original size Touch the inside OK keyNot copying onto a cover Cover CopyCopying onto a cover Select the covers that you wish to add Touch the OK key in the cover setting screenLoad the cover paper to be used into the bypass tray Specify whether or not the front cover is to be copied onThis is used to print a setting list or a font list. p.52 Custom SettingsContinuous printing. p.52 ProgrammedCustom Settings General Procedure for Custom SettingsSettings Touch the STORE/DELETE key JOB Program MemoryStoring a JOB Program Deleting a Stored JOB Program Executing a JOB ProgramPress the key Touch the program number key of the desired programCopying When Auditing Mode is Enabled Auditing ModeWhen the copy job is finished, press the ACC.#-C key Enter your account number 5 digits with the numeric keysImage quality problems Trouble Problems related to machine operationPaper feeding problems Display Messages Message Cause and solutionStaples are jammed in the finisher or the staple case is not Contact your authorised service representativeProblems related to machine operation TroubleshootingOriginal is not a standard size Automatically, or copying does notCopy, print job, or received fax is being printed Originals were being scannedPaper feeding problems Image quality problems First, locate the misfeed Misfeed RemovalMisfeed Removal Guidance Remove the misfed original Misfeed in the RspfSection C Section aMisfeed in the paper feed area Misfeed in the Bypass TrayMisfeed in the Machine Close the front cover and side cover Misfeed in the fusing areaTurn the roller rotating knob in the direction of the arrow Make sure that the misfeed message is clearedReplace the upper paper tray Misfeed in the Centre TrayMisfeed in the Upper Paper Tray Open the lower side cover Remove the misfed paper Misfeed in the Lower Paper TrayReplace the lower paper tray Close the lower side coverGently pull the misfed paper out Misfeed in the Upper Exit AreaMisfeed in AN Output Tray Troubleshooting and Maintenance Close the front cover Replacing the Toner CartridgeStaple Cartridge Replacement Checking the total output count and toner quantity Checking the Toner Quantity and Total Output CountStaple JAM Removal Document Glass and Document COVER/RSPF Cleaning the MachineBypass Tray Paper Feed Roller Surface of document glass Underside of document cover/RSPFReversing Single Pass Feeder AR-RP7 See Peripheral DevicesPart names SpecificationsFinisher AR-FN5N Capacity Lower tray Sheet Paper Feed UnitPaper Upper tray Reversing Single Pass Feeder Storage of SuppliesProper Storage Store the supplies in a location that isSpecifications Power consumption ResolutionOverall dimensions Developer systemSupplier Identification Sharp Corporation Product NameEnvironmental Precautions Personal PrecautionsMethods for Cleaning Up Most Important Hazards and Effects of the ProductsPersonal Protective Equipment Exposure limit valuesAppearance Boiling/Melting PointHuman exposures 4/4Chronic Effect Msds No. F-31201 Data Issued AugAR-271ND / AR-271DV / AR-271SD / AR-271SD-C Black Developer Ingredient CAS No ProportionData Issued Aug Msds No. F-31201 Acute Toxicity Toxicological InformationDisposal Considerations Index SymbolsImportant points when inserting paper How to place the originalImportant points when selecting an installation site Job programPower save modes Points to note when making copiesSetting the paper type in the bypass tray 15, 19Troubleshooting and maintenance Using convenient copy functionsPreparations Making copiesMemo Memo Memo Class Laser Product Laser Klasse Mains Plug Wiring Instructions 2003H KS ➀

Related manuals

Sharp AR-M236, AR-M276 Automatic TWO-SIDED Copying, Using the Document Glass, Original → Paper