Sharp PN-R603, PN-R703 operation manual Setting of the Gamma user data

Page 36

Controlling the Monitor with a PC (RS-232C)

nRepeater control

This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers.

[Example]

Set 1

 

Set 2

 

Set 3

 

Set 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setting of the GAMMA user data

nTo transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and UGBW). For each of the R, G and B colors, divide the total 512 pieces of user data into 16 blocks, and transfer 32 pieces of data with each command.

C1 C2 C3 C4 P1 P2 P3 P4 S1 S2

Command field Block number (01 to 16) Data field Checksum field

*If monitors are connected as shown above, you can execute a command like “Set all monitors’ input settings to

D-SUB[RGB]”.

nRepeater control command

Repeater control is achieved by setting the FOURTH CHARACTER of the parameter to “+”.

Example:

VOLM030 +

Sets volume of all monitors to 30.

In repeater control, responses are returned by all the connected monitors.

If you want to determine that a value has been returned by a specific set, assign ID numbers to each monitor in advance. When some monitors do not return their responses, the probable cause is that the monitors could not receive the command or command processing is not complete. Do not send a new command.

Example: (When 4 monitors are connected, and assigned ID numbers: 1 through 4)

VOLM030 +

WAIT

OK 001

OK 002

OK 003

OK 004 ← If 4 monitors are connected in

a chain, reliable operation can be ensured by sending a new command only after a reply has been returned by 4th (last) monitor.

Repeater control can also be used for reading settings.

Example: To transfer the data of block 1 (0 to 31 levels)

of red (R) data

UGRW01000000010002 … 0031C0

One piece of data consists

of 4 digits.

Command Block number 32 pieces of data

Checksum

*If data is less than 4 digits, add a “0” (zero) to make it 4 digits.

*The checksum field is the character string (ASCII) data of lower-order one byte which indicates the sum of the block number and 32 pieces of data in hexadecimal (0 to F).

nSaving the GAMMA user data

Use the user data save command (UGSV) to save the transferred user data in the monitor.

If the data is not saved, it will be cleared when:

The main power switch is off

STANDBY MODE is LOW POWER and the monitor enters standby mode

nActivating the GAMMA user data

To activate the transferred user data, select USER for GAMMA of the PICTURE menu, or send the corresponding RS-232C command.

nChecking the GAMMA user data

Use the user data read commands (UGRR, UGGR and UGBR) to return 512 pieces of user data for each of the R, G and B colors. Divide the data into 16 blocks and return 32 pieces of data with each command. The value to be returned is not the value stored in the monitor, but the value in the temporary memory for display. (These values are the same when the user data save command (UGSV) above has been sent.)

Example:

VOLM ? ? ? +

WAIT

10001

20002

30003

30004

Volume settings for all monitors are returned.

TIPS

The user data is not initialized by RESET of the PICTURE menu. To initialize the user data, use ALL RESET of the

FUNCTION menu.

The GAMMA user data initialize command (UGRS) allows the initialization of the user data only.

TIPS

If repeater control is used during ID designation (IDSL,

IDLK), the ID designation is canceled.

E36

Image 36
Contents PN-R703 PN-R603 Model No Serial No A. onlyRefer Servicing to Qualified Service Personnel Important InformationDear Sharp Customer Safety Precautions Tips and Safety Instructions Necessary to replace the LED backlightFor the monitor in landscape orientation For the monitor in portrait orientationContents Supplied ComponentsPart Names NFront viewNRear view Part Names NRemote control unit Signal transmitterPower button See Mute button See Return button See Size button SeeConnecting Peripheral Equipment 11 EConnection with a PC or AV equipment Connecting Peripheral Equipment Connecting the Power Cord 13 EBinding Cables Cable Cable clamp attachmentPreparing the Remote Control Unit Installing the batteriesRemote control operation range 15 ETurning Power On/Off Turning on the main powerTurning power on/off Main power switchDisabling power on/off operations NDate/time settingTurning Power On/Off 17 EBasic Operation Basic Operation NSwitching the screen size 19 EWide Zoom Normal Dot by DotMenu Items Displaying the menu screenNExample of operation NMenu screen display21 E Menu item detailsMenu Items NSCREENMenu Items NPICTURE 23 E Advanced3D-Y/C D-SUBVIDEO Display Color PatternNSETUP Menu Items NAUDIO25 E Menu Items NMONITOR 27 E Menu Items NMULTI/PIPMenu Items NOTHERS NZOOM2 Special Setting 29 ENDual screen display Menu Items NEnlargePower Menu Items NSCHEDULEDAY of the Week InputAdjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment 31 EALL Reset Adjustment LockAdjustment Lock Target Temperature AlertCommunication procedure Controlling the Monitor with a PC RS-232C33 E PC connectionNCommunication interval NID numbers35 E Wait ←Setting of the Gamma user data RS-232C command table Power control/Input mode selectionHow to read the command table 37 EControlling the Monitor with a PC RS-232C Screen menu Picture menu39 E Audio menuControlling the Monitor with a PC RS-232C Setup menu 41 E Controlling the Monitor with a PC RS-232C Monitor menuImage Position Epos setting Controlling the Monitor with a PC RS-232C MULTI/PIP menuLandscape orientation Portrait orientation 43 E Others menuCommands for setting of the Gamma user data OthersSettings to connect to a LAN Controlling the Monitor with a PC LAN45 E To set on the monitorDefault Gateway 0.0 Controlling the Monitor with a PC LAN To set from a PC47 E Controlling with a PCControlling the Monitor with a PC LAN Basic operationStandby mode, Power on is the operation available Information about this monitor appearsUser Name / Password 49 EDNS Server Address Auto Acquisition DNS ServerInstallation Information NAME/LOCATION Link ModeAuthentication Account Name / Password51 E Recipient E-MAIL AddressesCondition ConfirmationSnmp Setting Trap SettingTrap Setting of Authentication Error Version53 E Troubleshooting Troubleshooting 55 ESpecifications NProduct SpecificationsNDimensional Drawings Specifications57 E Specifications NPower management Dmpm Digital Monitor Power ManagementNDDC plug and play Specifications NCompatible signal timing PC NCompatible signal timing AV59 E NPC/AV D-sub input terminal pins NRS-232C input terminal pinsNDisplayPort input terminal pins NDVI-D output terminal pins NDisplayPort output terminal pinsSpecifications NRS-232C output terminal pins 61 EMounting Precautions For Sharp dealers and service engineers PN-R703R603 Mu EN12M1
Related manuals
Manual 63 pages 20.43 Kb Manual 28 pages 3.2 Kb

PN-R703, PN-R603 specifications

The Sharp PN-R603 and PN-R703 are advanced commercial display monitors designed to deliver high-quality visuals and reliable performance for a variety of applications. These models are part of Sharp’s professional display lineup, making them ideal for environments such as retail stores, conference rooms, and control centers.

One of the standout features of the PN-R603 and PN-R703 is their exceptional image quality. Both models utilize Sharp’s innovative LCD technology, which ensures stunning color reproduction and clarity. With a native resolution of 1920 x 1080 pixels, these displays present clear, detailed images that are perfect for showcasing videos, presentations, or advertising content. The brightness of up to 700 cd/m² ensures visibility even in well-lit environments, making them practical for almost any setting.

Both models incorporate an ultra-slim design, allowing for seamless integration into any environment. Whether mounted on walls or placed on stands, the PN-R603 and PN-R703 maintain an elegant profile that enhances their surroundings. The frameless bezel design further maximizes the viewing area, creating an immersive experience for users.

In terms of connectivity, these displays offer a comprehensive suite of options. HDMI, DisplayPort, and VGA inputs facilitate quick and easy connections to various devices, including computers, media players, and video conferencing systems. This flexibility enables users to seamlessly switch between different formats and sources without hassle.

The PN-R603 and PN-R703 are not just visually appealing; they are also designed for durability and reliability. With a robust construction that supports continuous operation, these displays are well-suited for 24/7 use, making them ideal for mission-critical applications. The built-in cooling system ensures optimal performance while minimizing the risk of overheating, thus extending the lifespan of the units.

Additionally, both models come equipped with essential features such as integrated USB media playback, allowing users to display content directly from USB drives without requiring a connected PC. This feature streamlines the process of sharing information and makes setting up presentations easier.

In summary, the Sharp PN-R603 and PN-R703 exhibit a host of features that cater to the needs of professional environments. From their stunning display quality and versatile connectivity options to their durable construction and ease of use, these monitors represent a robust solution for businesses looking to enhance their visual communications. Whether for advertising, presentations, or information displays, the PN-R603 and PN-R703 stand out as reliable and effective choices.