Sharp PN-R703 47 E, Controlling with a PC, Controlling the Monitor with a PC LAN, Basic operation

Page 47

5. Click on “LAN SETUP” under NETWORK.

6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.

Controlling the Monitor with a PC (LAN)

Controlling with a PC

■ Basic operation

You use Internet Explorer on a PC on the LAN to control the monitor.

1.Launch Internet Explorer on the PC.

2.In the “Address” box, type “http://” followed by your monitor’s IP address followed by “/”, then press the Enter key.

You can confirm the IP address with the DISPLAY function.

When prompted to enter a user name and password, type the user name and password that you specified in the security settings (see page 49), and click [OK].

3.You can check, control, and change the monitor’s status and settings by clicking the menu items on the left side of the screen.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”.

To set the address manually, set this to “OFF”.

IP ADDRESS

If the DHCP CLIENT is set to “OFF”, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to “OFF”, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to “OFF”, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

7.When the setting is changed, click [Apply].

8.Check the message and click [OK].

9.Exit Internet Explorer.

10.Restore the PC’s IP address jotted in Step 6, “(2)

Specifying the PC’s IP address”.

11. Connect the monitor and the PC to the LAN.

Caution

•Wait 10 seconds after clicking [OK] before proceeding.

•When operating using the remote control unit or similar, click [Refresh].

TIPS

•When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

•If you see an [Apply] button next to a setting, click it after you change that setting.

TIPS

•See pages 48 to 52 for details on each setting.

•If you click [Refresh] before the screen finishes updating the current display, the “Server Busy Error” will appear. Wait for a moment before operating your monitor again.

•You cannot operate the monitor while it is warming up.

•If “DHCP CLIENT” is set to “ON”, press DISPLAY on the remote control unit two times and then check the monitor’s

IP address.

47 E

Page 46 Page 48
Image 47
Page 46 Page 48
Contents PN-R703 PN-R603 A. only Model No Serial NoImportant Information Refer Servicing to Qualified Service PersonnelDear Sharp Customer Safety Precautions Necessary to replace the LED backlight Tips and Safety InstructionsFor the monitor in portrait orientation For the monitor in landscape orientationSupplied Components ContentsNRear view Part NamesNFront view Return button See Size button See Part Names NRemote control unitSignal transmitter Power button See Mute button SeeConnection with a PC or AV equipment Connecting Peripheral Equipment11 E Connecting Peripheral Equipment 13 E Connecting the Power CordCable Cable clamp attachment Binding Cables15 E Preparing the Remote Control UnitInstalling the batteries Remote control operation rangeMain power switch Turning Power On/OffTurning on the main power Turning power on/off17 E Disabling power on/off operationsNDate/time setting Turning Power On/OffBasic Operation Dot by Dot Basic Operation NSwitching the screen size19 E Wide Zoom NormalNMenu screen display Menu ItemsDisplaying the menu screen NExample of operationNSCREEN 21 EMenu item details Menu ItemsMenu Items NPICTURE Display Color Pattern 23 EAdvanced 3D-Y/C D-SUBVIDEOMenu Items NAUDIO NSETUP25 E Menu Items NMONITOR Menu Items NMULTI/PIP 27 EMenu Items NOTHERS Menu Items NEnlarge NZOOM2 Special Setting29 E NDual screen displayInput PowerMenu Items NSCHEDULE DAY of the Week31 E Adjustments for PC screen displayNAutomatic adjustment NScreen display for adjustmentTemperature Alert ALL ResetAdjustment Lock Adjustment Lock TargetPC connection Communication procedureControlling the Monitor with a PC RS-232C 33 ENID numbers NCommunication intervalWait ← 35 ESetting of the Gamma user data 37 E RS-232C command tablePower control/Input mode selection How to read the command tablePicture menu Controlling the Monitor with a PC RS-232C Screen menuAudio menu 39 EControlling the Monitor with a PC RS-232C Setup menu Controlling the Monitor with a PC RS-232C Monitor menu 41 ELandscape orientation Portrait orientation Image Position Epos settingControlling the Monitor with a PC RS-232C MULTI/PIP menu Others menu 43 E Others Commands for setting of the Gamma user dataTo set on the monitor Settings to connect to a LANControlling the Monitor with a PC LAN 45 EControlling the Monitor with a PC LAN To set from a PC Default Gateway 0.0Basic operation 47 EControlling with a PC Controlling the Monitor with a PC LANInformation about this monitor appears Standby mode, Power on is the operation availableDNS Server User Name / Password49 E DNS Server Address Auto AcquisitionAccount Name / Password Installation Information NAME/LOCATIONLink Mode AuthenticationConfirmation 51 ERecipient E-MAIL Addresses ConditionVersion Snmp SettingTrap Setting Trap Setting of Authentication Error53 E Troubleshooting 55 E TroubleshootingNProduct Specifications Specifications57 E NDimensional DrawingsSpecifications NDDC plug and play Specifications NPower managementDmpm Digital Monitor Power Management 59 E Specifications NCompatible signal timing PCNCompatible signal timing AV NDisplayPort input terminal pins NPC/AV D-sub input terminal pinsNRS-232C input terminal pins 61 E NDVI-D output terminal pinsNDisplayPort output terminal pins Specifications NRS-232C output terminal pinsMounting Precautions For Sharp dealers and service engineers PN-R703R603 Mu EN12M1
Related manuals
Manual 63 pages 20.43 Kb Manual 28 pages 3.2 Kb
Top Page Image Contents