Vizio TL-WR641G manual

Page 24

TL-WR641G

108M Wireless Router User Guide

Dynamic IP. If you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and a password, please select the type of your ISP provided (PPPoE/BigPond/L2TP/PPTP). If you are not sure which connection type you use currently, please contact your ISP to obtain the correct information.

1.If you choose Dynamic IP, the router will automatically get IP parameters from your ISP. You can see the page as follows (Figure 4-4):

Figure 4-4

This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.

¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.

¾Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP.

)Note:

If you get address and find error when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.

- 16 -

Image 24
Contents TL-WR641G Copyright & Trademarks FCC Statement National Restrictions Page Package contents Contents 11.1 Features Overview of the RouterPanel Layout Front PanelRear Panel LEDs descriptionIndication ¾ Reset button ¾ Wireless antennaInstallation Environment Requirements Connecting the RouterSystem Requirements Power on your PC and Cable/DSL Modem Quick Installation Guide TCP/IP configurationPlease check the connection following these steps Quick Installation Guide TL-WR641G IP parameters should have been provided by your ISP TL-WR641G Login StatusQuick Setup Network 1 LAN2 WAN TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G NSW / ACT nsw.bigpond.net.au QLD qld.bigpond.net.auTL-WR641G TL-WR641G TL-WR641G MAC Clone Wireless Wireless SettingsTL-WR641G TL-WR641G TL-WR641G TL-WR641G MAC Filtering TL-WR641G TL-WR641G Wireless Statistics Dhcp Settings DhcpDhcp Clients List Address ReservationTo Reserve IP addresses To setup a virtual server entry ForwardingVirtual Servers TL-WR641G Port Triggering TL-WR641G 3 DMZ UPnPSecurity FirewallIP Address Filtering TL-WR641G Domain Filtering TL-WR641G MAC Filtering TL-WR641G Remote Management Advanced SecurityTL-WR641G IP & MAC Binding Setting Binding SettingTo add IP & MAC Binding entries To modify or delete an existing entryTo find an existing entry ARP List Static Routing To add static routing entriesDdns Dyndns.org DdnsOray.net Ddns Comexe.cn DdnsSystem Tools Select using daylight saving time TimeFactory Defaults FirmwareBackup and Restore RebootPassword 12.7 LogStatistics ¾ Statistics Table TCPAppendix a FAQ Figure A-3 Want to use Netmeeting, what do I need to do?Figure A-5 Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the router Figure A-8Appendix B Configuring the PC Install TCP/IP componentShown in the Figure below ¾ Setting IP address manually TL-WR641G General Environmental and PhysicalAppendix D Glossary TL-WR641G