Vizio TL-WR641G manual Domain Filtering

Page 55

TL-WR641G

108M Wireless Router User Guide

4.WAN IP Address - Enter a WAN IP Address or a range of WAN IP Addresses in the field, in dotted-decimal notation format. For example, 61.145.238.6 – 61.145.238.47. Keep the field open, which means all WAN IP Addresses have been put into the field.

5.WAN Port - Enter a WAN Port or a range of WAN Ports in the field. For example, 25 – 110. Keep the field open, which means all WAN Ports have been put into the field.

6.Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols supported by the router).

7.Action - Select either Allow or Deny through the router.

8.Status - Select Enabled or Disabled for this entry on the Status pull-down list.

9.Click the Save button to save this entry.

To modify or delete an existing entry:

1.Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete.

2.Modify the information.

3.Click the Save button.

Click the Enable All button to make all entries enabled

Click the Disabled All button to make all entries disabled.

Click the Delete All button to delete all entries

You can change the entry’s order as desired. Fore entries are before hind entries. Enter the ID number in the first box you want to move and another ID number in second box you want to move to, and then click the Move button to change the entry’s order.

Click the Next button to the next page and click the Previous button to return to the previous page.

For example: If you desire to block E-mail received and sent by the IP Address 192.168.1.7 on your local network, and to make the PC with IP Address 192.168.1.8 unable to visit the website of IP Address 202.96.134.12, while other PC(s) have no limit you should specify the following IP address filtering list:

Figure 4-39

4.8.3 Domain Filtering

The Domain Filtering page (shown in Figure 4-40)allows you to control access to certain websites on the Internet by specifying their domains or key words.

- 47 -

Image 55
Contents TL-WR641G Copyright & Trademarks FCC Statement National Restrictions Page Package contents Contents 11.1 Overview of the Router FeaturesFront Panel Panel LayoutLEDs description Rear PanelIndication ¾ Wireless antenna ¾ Reset buttonConnecting the Router Installation Environment RequirementsSystem Requirements Power on your PC and Cable/DSL Modem TCP/IP configuration Quick Installation GuidePlease check the connection following these steps Quick Installation Guide TL-WR641G IP parameters should have been provided by your ISP TL-WR641G Status LoginQuick Setup 1 LAN Network2 WAN TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G QLD qld.bigpond.net.au NSW / ACT nsw.bigpond.net.auTL-WR641G TL-WR641G TL-WR641G MAC Clone Wireless Settings WirelessTL-WR641G TL-WR641G TL-WR641G TL-WR641G MAC Filtering TL-WR641G TL-WR641G Wireless Statistics Dhcp Dhcp SettingsAddress Reservation Dhcp Clients ListTo Reserve IP addresses Forwarding To setup a virtual server entryVirtual Servers TL-WR641G Port Triggering TL-WR641G UPnP 3 DMZFirewall SecurityIP Address Filtering TL-WR641G Domain Filtering TL-WR641G MAC Filtering TL-WR641G Advanced Security Remote ManagementTL-WR641G Binding Setting IP & MAC Binding SettingTo modify or delete an existing entry To add IP & MAC Binding entriesTo find an existing entry ARP List To add static routing entries Static RoutingDyndns.org Ddns DdnsComexe.cn Ddns Oray.net DdnsSystem Tools Time Select using daylight saving timeFirmware Factory DefaultsReboot Backup and Restore12.7 Log PasswordStatistics TCP ¾ Statistics TableAppendix a FAQ Want to use Netmeeting, what do I need to do? Figure A-3Want to build a WEB Server on the LAN, what should I do? Figure A-5Figure A-8 Wireless stations cannot connect to the routerInstall TCP/IP component Appendix B Configuring the PCShown in the Figure below ¾ Setting IP address manually TL-WR641G Environmental and Physical GeneralAppendix D Glossary TL-WR641G