Vizio TL-WR641G manual Dhcp Clients List, Address Reservation

Page 45

TL-WR641G

108M Wireless Router User Guide

¾Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the router, default value is 192.168.1.1

¾Default Domain - (Optional.) Input the domain name of your network.

¾Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your ISP.

¾Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers.

)Note:

To use the DHCP server function of the router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. This function will take effect until the router reboots.

4.6.2 DHCP Clients List

This page shows Client Name, MAC Address, Assigned IP, and Lease Time for each DHCP Client attached to the router (Figure 4-25):

Figure 4-25

¾Index - The index of the DHCP Client

¾Client Name - The name of the DHCP client

¾MAC Address - The MAC address of the DHCP client

¾Assigned IP - The IP address that the router has allocated to the DHCP client.

¾Lease Time - The time of the DHCP client leased. Before the time is up, DHCP client will request to renew the lease automatically.

You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button.

4.6.3 Address Reservation

When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings. This page is used for address reservation (shown in Figure 4-26).

- 37 -

Image 45
Contents TL-WR641G Copyright & Trademarks FCC Statement National Restrictions Page Package contents Contents 11.1 Overview of the Router FeaturesFront Panel Panel LayoutRear Panel LEDs descriptionIndication ¾ Wireless antenna ¾ Reset buttonInstallation Environment Requirements Connecting the RouterSystem Requirements Power on your PC and Cable/DSL Modem TCP/IP configuration Quick Installation GuidePlease check the connection following these steps Quick Installation Guide TL-WR641G IP parameters should have been provided by your ISP TL-WR641G Status LoginQuick Setup Network 1 LAN2 WAN TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G QLD qld.bigpond.net.au NSW / ACT nsw.bigpond.net.auTL-WR641G TL-WR641G TL-WR641G MAC Clone Wireless Settings WirelessTL-WR641G TL-WR641G TL-WR641G TL-WR641G MAC Filtering TL-WR641G TL-WR641G Wireless Statistics Dhcp Dhcp SettingsAddress Reservation Dhcp Clients ListTo Reserve IP addresses To setup a virtual server entry ForwardingVirtual Servers TL-WR641G Port Triggering TL-WR641G UPnP 3 DMZFirewall SecurityIP Address Filtering TL-WR641G Domain Filtering TL-WR641G MAC Filtering TL-WR641G Advanced Security Remote ManagementTL-WR641G Binding Setting IP & MAC Binding SettingTo add IP & MAC Binding entries To modify or delete an existing entryTo find an existing entry ARP List To add static routing entries Static RoutingDyndns.org Ddns DdnsComexe.cn Ddns Oray.net DdnsSystem Tools Time Select using daylight saving timeFirmware Factory DefaultsReboot Backup and Restore12.7 Log PasswordStatistics TCP ¾ Statistics TableAppendix a FAQ Want to use Netmeeting, what do I need to do? Figure A-3Want to build a WEB Server on the LAN, what should I do? Figure A-5Figure A-8 Wireless stations cannot connect to the routerInstall TCP/IP component Appendix B Configuring the PCShown in the Figure below ¾ Setting IP address manually TL-WR641G Environmental and Physical GeneralAppendix D Glossary TL-WR641G