Vizio TL-WR641G manual

Page 41

TL-WR641G

108M Wireless Router User Guide

¾WEP Key - Specify a unique WEP key (in Hexadecimal format) to access the router. To set up an entry, follow these instructions:

First, you must decide whether the unspecified wireless stations can access the router or not. If you desire that the unspecified wireless stations can access the router, please select the radio button Allow the stations not specified by any enabled entries in the list to access, otherwise, select the radio button Deny the stations not specified by any enabled entries in the list to access.

To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-20:

Figure 4-20

To add or modify a MAC Address Filtering entry, follow these instructions:

1.Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B.

2.Enter a simple description of the wireless station in the Description field. For example: Wireless station A.

3.Privilege - Select the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit.

4.WEP Key - If you select 64-bit, 128-bitor 152-bitin the Privilege field, enter any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. For example: 2F34D20BE2.

5.Status - Select Enabled or Disabled for this entry on the Status pull-down list.

6.Click the Save button to save this entry.

To add additional entries, repeat steps 1-6.

)Note:

When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled.

- 33 -

Image 41
Contents TL-WR641G Copyright & Trademarks FCC Statement National Restrictions Page Package contents Contents 11.1 Overview of the Router FeaturesFront Panel Panel LayoutIndication Rear PanelLEDs description ¾ Wireless antenna ¾ Reset buttonSystem Requirements Installation Environment RequirementsConnecting the Router Power on your PC and Cable/DSL Modem TCP/IP configuration Quick Installation GuidePlease check the connection following these steps Quick Installation Guide TL-WR641G IP parameters should have been provided by your ISP TL-WR641G Status LoginQuick Setup 2 WAN Network1 LAN TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G TL-WR641G QLD qld.bigpond.net.au NSW / ACT nsw.bigpond.net.auTL-WR641G TL-WR641G TL-WR641G MAC Clone Wireless Settings WirelessTL-WR641G TL-WR641G TL-WR641G TL-WR641G MAC Filtering TL-WR641G TL-WR641G Wireless Statistics Dhcp Dhcp SettingsAddress Reservation Dhcp Clients ListTo Reserve IP addresses Virtual Servers To setup a virtual server entryForwarding TL-WR641G Port Triggering TL-WR641G UPnP 3 DMZFirewall SecurityIP Address Filtering TL-WR641G Domain Filtering TL-WR641G MAC Filtering TL-WR641G Advanced Security Remote ManagementTL-WR641G Binding Setting IP & MAC Binding SettingTo find an existing entry To add IP & MAC Binding entriesTo modify or delete an existing entry ARP List To add static routing entries Static RoutingDyndns.org Ddns DdnsComexe.cn Ddns Oray.net DdnsSystem Tools Time Select using daylight saving timeFirmware Factory DefaultsReboot Backup and Restore12.7 Log PasswordStatistics TCP ¾ Statistics TableAppendix a FAQ Want to use Netmeeting, what do I need to do? Figure A-3Want to build a WEB Server on the LAN, what should I do? Figure A-5Figure A-8 Wireless stations cannot connect to the routerInstall TCP/IP component Appendix B Configuring the PCShown in the Figure below ¾ Setting IP address manually TL-WR641G Environmental and Physical GeneralAppendix D Glossary TL-WR641G