AMX NXI-x000 Series manual Removing NetLinx Control Cards NI-4000 Only, Compact Flash Upgrades

Page 21

Installation and Upgrading

NUMBER:PORT:SYSTEM

where:

NUMBER:

16-bit integer represents the device number

PORT:

16-bit integer represents the port number (in the range 1 through the number of

 

ports on the Controller or device)

SYSTEM:

16-bit integer represents the system number (0 = this system)

Removing NetLinx Control Cards (NI-4000 Only)

To install NetLinx Control Card:

1.Discharge any static electricity from your body, by touching a grounded object and unplug all connectors (if any) from the unit.

2.Remove the three faceplate screws by turning them in a counter-clockwise direction.

3.Remove the faceplate from the front plate (FIG. 1 on page 15).

4.Gently grasp the rear edge of the control card and gently pull it out from the unit (along the internal guide slots).

5.Re-secure the faceplate by inserting the three faceplate screws by turning them in a clockwise direction and securing the front plate to the Integrated Controller.

6.Re-apply power and other connections as necessary.

Compact Flash Upgrades

The NetLinx Integrated Controllers are shipped with a default 32 MB Compact Flash module.

It is recommended that ANY MEMORY UPGRADE should be done prior to any installation. Refer to the following accessing and installation sections for more information.

The Compact Flash card is factory programmed with specific Controller firmware. These cards can be ordered from AMX in several different upgrade sizes (see the following table):

Optional Compact Flash Upgrades

Product Name

Description

 

 

NXA-CFNI64M

64 MB compact flash card (FG2116-31)

 

 

NXA-CFNI128M

128 MB compact flash card (FG2116-32)

 

 

NXA-CFNI256M

256 MB compact flash card (FG2116-33)

 

 

NXA-CFNI512M

512 MB compact flash card (FG2116-34)

 

 

NXA-CFNI1G

1 GB compact flash card (FG2116-35)

 

 

Accessing The Internal Components On An Integrated Controller

1.Carefully detach all connectors from the rear of the unit.

2.Remove the chassis housing screws from both the sides and top of the Controller, as shown in FIG. 3 by using a grounded screwdriver turning in a counter-clockwise rotation.

The NI-2000 and NI-3000 have six screws on top and three on each side.

The NI-4000 has six screws on top and four on each side.

NI-2000, NI-3000, NI-4000 Hardware Reference Guide

17

 

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents Introduction NetLinx Integrated Master Controller FeaturesRear NI-2000 SpecificationsNI-2000 Specifications Rear Panel ConnectorsFront Panel Components Surge damage NI-2000 Specifications NI-3000 NetLinx Integrated Controller front view NI-3000 SpecificationsNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 NetLinx Integrated Controller front view NI-4000 SpecificationsNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installing NetLinx Control Cards NI-4000 Only Installation and UpgradingSetting the NetLinx Control Card Addresses NI-4000 Only DevicePortSystem DPSPosition Optional Compact Flash Upgrades Compact Flash UpgradesRemoving NetLinx Control Cards NI-4000 Only Product Name DescriptionInstallation of Compact Flash Upgrades Closing and Securing the Outer Housing Installing Into An Equipment RackInstall screws Bracket Rack Mounting Holes Baud Rate Settings Setting the Configuration DIP Switch for the Program PortProgram Run Disable PRD Mode Baud Rate Settings on the Configuration DIP SwitchProgram Port Connections and Wiring Setting the CardFrame DIP Switch NI-4000 OnlyWorking With the Configuration DIP Switch Program Port, Pinouts, and SignalsPort Assignments and Functionality Modes and Front Panel LED Blink PatternsModes and LED Blink Patterns NI-2000 Port AssignmentsWiring length guidelines Wiring GuidelinesWiring Guidelines NI-2000 @ 700 mA Wiring Guidelines NI-3000 & NI-4000 @ 900 mAPreparing Captive Wires Wiring a Power ConnectionUsing the 4-Pin Mini-Phoenix Connector For Data and Power RS-232 RS-422 RS-485 DB9 Device Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications ICSNet Port Connections and WiringICSNet RJ-45 Signals RJ-45 Pinout Information EIA/TIA 568 BRelay Port Connections and Wiring ICSHub OUT Port Connections and WiringICSHub OUT Pinouts and Signals Relay ConnectionsInput/Output I/O Port Connections and Wiring Port Wiring Specifications NI-4000 and NI-3000Port Wiring Specifications NI-2000 NetLinx Control Card Slot Connector NI-4000 only IR/Serial Port Connections and WiringIR/Serial Connector Wiring Specifications per Port Signal FunctionEthernet RJ-45 Pinouts and Signals Ethernet/RJ-45 Port Connections and WiringPin Signals Connections Pairing Color Ethernet LEDsEthernet Ports Used By the Integrated Controller Ethernet Port DescriptionsPort type Description Standard Port # Page It’s Your World Take Control
Top Page Image Contents