AMX NXI-x000 Series NI-3000 Specifications, NI-3000 NetLinx Integrated Controller front view

Page 10

Introduction

NI-3000 Specifications

The front LEDs (FIG. 3) are grouped by control type and are labeled according to their corresponding port (connector) numbers on the rear of the unit. The back of the this unit contains RS-232/422/485, Relay, IR/Serial and I/O connectors. In addition, this unit provides an ID pushbutton, AXlink LED, and other related connectors. FIG. 4 shows the front and rear of the

NI-3000.

FIG. 3 NI-3000 NetLinx Integrated Controller (front view)

Link/Active-Status-Output-Input

RS-232/422/485 TX/RX LEDs (red/yellow)

Relay LEDs (red)

IR/Serial LEDs (red)

I/O LEDs (yellow)

Front

 

 

 

ICSNet (2)

AXlink LED

RS-232/422/485 (Ports 1-7)

ICSHub Out

(green)

Rear

 

Relays

 

IR/Serial (Ports 9-16)

(Port 8)

 

 

 

 

 

I/O (Port 17)

Program

DIP

 

port

switch

 

 

ID Pushbutton

Ethernet

AXlink port

PWR

FIG. 4 NI-3000 front and rear panel components

6

NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Page 9 Page 11
Image 10
Page 9 Page 11
Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NetLinx Integrated Master Controller Features IntroductionNI-2000 Specifications RearRear Panel Connectors NI-2000 SpecificationsFront Panel Components Surge damage NI-2000 Specifications NI-3000 Specifications NI-3000 NetLinx Integrated Controller front viewNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 Specifications NI-4000 NetLinx Integrated Controller front viewNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installation and Upgrading Installing NetLinx Control Cards NI-4000 OnlyDevicePortSystem DPS Setting the NetLinx Control Card Addresses NI-4000 OnlyPosition Removing NetLinx Control Cards NI-4000 Only Compact Flash UpgradesOptional Compact Flash Upgrades Product Name DescriptionInstallation of Compact Flash Upgrades Installing Into An Equipment Rack Closing and Securing the Outer HousingInstall screws Bracket Rack Mounting Holes Program Run Disable PRD Mode Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Baud Rate Settings on the Configuration DIP SwitchWorking With the Configuration DIP Switch Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Program Port, Pinouts, and SignalsModes and LED Blink Patterns Modes and Front Panel LED Blink PatternsPort Assignments and Functionality NI-2000 Port AssignmentsWiring Guidelines NI-2000 @ 700 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-3000 & NI-4000 @ 900 mAWiring a Power Connection Preparing Captive WiresUsing the 4-Pin Mini-Phoenix Connector For Data and Power DB9 Device Port Connections and Wiring RS-232 RS-422 RS-485ICSNet RJ-45 Signals ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications RJ-45 Pinout Information EIA/TIA 568 BICSHub OUT Pinouts and Signals ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring Relay ConnectionsPort Wiring Specifications NI-4000 and NI-3000 Input/Output I/O Port Connections and WiringPort Wiring Specifications NI-2000 IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only Signal FunctionPin Signals Connections Pairing Color Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Ethernet LEDsEthernet Port Descriptions Ethernet Ports Used By the Integrated ControllerPort type Description Standard Port # Page It’s Your World Take Control
Top Page Image Contents