AMX NXI-x000 Series Installing Into An Equipment Rack, Closing and Securing the Outer Housing

Page 23

Installation and Upgrading

Under-side groove

located below

Card Removal Grooves

Insert with arrow facing towards the connector pins

FIG. 4 Removing the Compact Flash card

7.To complete the upgrade process, close and re-secure the Integrated Controller enclosure using the procedures outlined in the following section.

Any new internal card upgrade is detected by the Controller only after power is cycled.

Closing and Securing the Outer Housing

Once the card has been replaced, close and re-secure the outer housing:

1.Align the cover back over the unit and gently slide-down the chassis until the openings are aligned over their respective openings along both the sides and top of the unit.

2.Insert and secure the chassis housing screws back into their respective locations, as shown in FIG. 3 by using a grounded screwdriver.

3.Re-install all connectors and apply power to the unit.

Installing Into An Equipment Rack

Use the rack-mounting brackets (supplied) for equipment rack installations.

Remove the mounting brackets for flat surface installations.

Before completing the install process, it is recommended that you complete any firmware upgrade of the NetLinx Control Cards. This upgrade involves physically cycling power to the unit and can become cumbersome if the unit is already installed into a rack. Refer to theUpgrading the NXC Card Firmware via IP (NI-4x00 ONLY) section on page 59 for more detailed information.

1.Discharge the static electricity from your body by touching a grounded object.

2.Position and install the mounting brackets, as shown in FIG. 5, using the screws supplied with the unit. The mounting brackets can be rotated to accommodate your mounting needs.

NI-2000, NI-3000, NI-4000 Hardware Reference Guide	19

Image 23

Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents Introduction NetLinx Integrated Master Controller FeaturesRear NI-2000 SpecificationsFront Panel Components NI-2000 SpecificationsRear Panel Connectors Surge damage NI-2000 Specifications NI-3000 NetLinx Integrated Controller front view NI-3000 SpecificationsNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 NetLinx Integrated Controller front view NI-4000 SpecificationsNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installing NetLinx Control Cards NI-4000 Only Installation and UpgradingPosition Setting the NetLinx Control Card Addresses NI-4000 OnlyDevicePortSystem DPS Product Name Description Compact Flash UpgradesOptional Compact Flash Upgrades Removing NetLinx Control Cards NI-4000 OnlyInstallation of Compact Flash Upgrades Closing and Securing the Outer Housing Installing Into An Equipment RackInstall screws Bracket Rack Mounting Holes Baud Rate Settings on the Configuration DIP Switch Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Program Run Disable PRD ModeProgram Port, Pinouts, and Signals Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Working With the Configuration DIP SwitchNI-2000 Port Assignments Modes and Front Panel LED Blink PatternsPort Assignments and Functionality Modes and LED Blink PatternsWiring Guidelines NI-3000 & NI-4000 @ 900 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-2000 @ 700 mAUsing the 4-Pin Mini-Phoenix Connector For Data and Power Preparing Captive WiresWiring a Power Connection RS-232 RS-422 RS-485 DB9 Device Port Connections and WiringRJ-45 Pinout Information EIA/TIA 568 B ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications ICSNet RJ-45 SignalsRelay Connections ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring ICSHub OUT Pinouts and SignalsPort Wiring Specifications NI-2000 Input/Output I/O Port Connections and WiringPort Wiring Specifications NI-4000 and NI-3000 Signal Function IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only IR/Serial Connector Wiring Specifications per PortEthernet LEDs Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Pin Signals Connections Pairing ColorPort type Description Standard Port # Ethernet Ports Used By the Integrated ControllerEthernet Port Descriptions Page It’s Your World Take Control