AMX NXI-x000 Series manual Setting the CardFrame DIP Switch NI-4000 Only

Page 26

Connections and Wiring

Think of the PRD Mode (On) equating to a PC’s SAFE Mode setting. This mode allows a user to continue powering a unit, update the firmware, and download a new program while circumventing any problems with a currently downloaded program. Power must be cycled to the unit after activating/deactivating this mode on the Program Port DIP switch #1.

Working With the Configuration DIP Switch

1.Disconnect the power supply from the 2-pin PWR (green) connector on the rear of the NetLinx Integrated Controller.

2.Set DIP switch positions according to the information listed in theBaud Rate Settings on the Configuration DIP Switch andPRD Mode Settings tables.

3.Reconnect the 12 VDC-compliant power supply to the 2-pin 3.5 mm mini-Phoenix PWR connector.

Setting the CardFrame DIP Switch (NI-4000 Only)

Refer to the Setting the NetLinx Control Card Addresses (NI-4000 Only) section on page 16 for a detailed explanation on this process.

Program Port Connections and Wiring

The Integrated Controllers are equipped with a Program port located on the front of the unit. Use an RS232 programming cable to establish a connection between this Program port to your PC's COM port. This connection provides communication with the NetLinx Integrated Controller. Then you can download NetLinx programs to this on-board Master using the NetLinx Studio v 2.4 software program. Refer to the NetLinx Studio instruction manual for programming instructions. The following table shows the rear panel Program Port connector (male), pinouts, and signals.

Program Port, Pinouts, and Signals

Program Port Connector

Pin Signal

2RX

3TX

5GND

	5	9	7	RTS
		8
	4		8	CTS

	3

2

1 7

6

Male

When wiring the 422/485 connections, do NOT use pre-made 9-wire cable or connect the wire in the cable to any connection that will not be used by the DB9 serial port. Only use wiring that connects the needed pins.

22	NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Image 26

Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NetLinx Integrated Master Controller Features IntroductionNI-2000 Specifications RearFront Panel Components NI-2000 SpecificationsRear Panel Connectors Surge damage NI-2000 Specifications NI-3000 Specifications NI-3000 NetLinx Integrated Controller front viewNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 Specifications NI-4000 NetLinx Integrated Controller front viewNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installation and Upgrading Installing NetLinx Control Cards NI-4000 OnlyPosition Setting the NetLinx Control Card Addresses NI-4000 OnlyDevicePortSystem DPS Removing NetLinx Control Cards NI-4000 Only Compact Flash UpgradesOptional Compact Flash Upgrades Product Name DescriptionInstallation of Compact Flash Upgrades Installing Into An Equipment Rack Closing and Securing the Outer HousingInstall screws Bracket Rack Mounting Holes Program Run Disable PRD Mode Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Baud Rate Settings on the Configuration DIP SwitchWorking With the Configuration DIP Switch Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Program Port, Pinouts, and SignalsModes and LED Blink Patterns Modes and Front Panel LED Blink PatternsPort Assignments and Functionality NI-2000 Port AssignmentsWiring Guidelines NI-2000 @ 700 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-3000 & NI-4000 @ 900 mAUsing the 4-Pin Mini-Phoenix Connector For Data and Power Preparing Captive WiresWiring a Power Connection DB9 Device Port Connections and Wiring RS-232 RS-422 RS-485ICSNet RJ-45 Signals ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications RJ-45 Pinout Information EIA/TIA 568 BICSHub OUT Pinouts and Signals ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring Relay ConnectionsPort Wiring Specifications NI-2000 Input/Output I/O Port Connections and WiringPort Wiring Specifications NI-4000 and NI-3000 IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only Signal FunctionPin Signals Connections Pairing Color Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Ethernet LEDsPort type Description Standard Port # Ethernet Ports Used By the Integrated ControllerEthernet Port Descriptions Page It’s Your World Take Control