AMX NXI-x000 Series manual ICSNet Port Connections and Wiring, ICSNet RJ-45 Signals

Page 31

Connections and Wiring

The table below provides information about the connector pins, signal types, and signal functions. This table’s wiring specifications are applicable to the rear RS-232/422/485 Device Port connectors on the:

NI-2000 (Ports 1-3)

NI-4000/NI-3000 (Ports 1-7)

RS-232/422/485 Device Port Wiring Specifications

Pin	Signal	Function	RS-232	RS-422	RS-485

1	RX-	Receive data		X	X (strap to pin 9)

2	RXD	Receive data	X

3	TXD	Transmit data	X

4	TX+	Transmit data		X	X (strap to pin 6)

5	GND	Signal ground	X	X

6	RX+	Receive data		X	X (strap to pin 4)

7	RTS	Request to send	X

8	CTS	Clear to send	X

9	TX-	Transmit data		X	X (strap to pin 1)

ICSNet Port: Connections and Wiring

The NI Controller must be equipped with the available ICSNet connectors for this functionality to be active. The following tables show the signal and pinouts/pairing information:

ICSNet RJ-45 Signals

Pin	Signal-Master	Signal-Device

1	TX +	RX +

2	TX -	RX -

3	N/A	N/A

4	GND	GND

5	N/A	N/A

6	N/A	N/A

7	RX +	TX +

8	RX -	TX -

RJ-45 Pinout Information (EIA/TIA 568 B)

Pin	Wire Color	Polarity	Function
1	Orange/White	+	Transmit

2	Orange	-	Transmit

3	Green/White	-	Mic

4	Blue	-	Ground

5	White/Blue	+	12 VDC

6	Green	+	Mic

7	White/Brown	+	Receive

8	Brown	-	Receive

TIA 568B

NI-2000, NI-3000, NI-4000 Hardware Reference Guide	27

Image 31

Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents Introduction NetLinx Integrated Master Controller FeaturesRear NI-2000 SpecificationsRear Panel Connectors NI-2000 SpecificationsFront Panel Components Surge damage NI-2000 Specifications NI-3000 NetLinx Integrated Controller front view NI-3000 SpecificationsNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 NetLinx Integrated Controller front view NI-4000 SpecificationsNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installing NetLinx Control Cards NI-4000 Only Installation and UpgradingDevicePortSystem DPS Setting the NetLinx Control Card Addresses NI-4000 OnlyPosition Product Name Description Compact Flash UpgradesOptional Compact Flash Upgrades Removing NetLinx Control Cards NI-4000 OnlyInstallation of Compact Flash Upgrades Closing and Securing the Outer Housing Installing Into An Equipment RackInstall screws Bracket Rack Mounting Holes Baud Rate Settings on the Configuration DIP Switch Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Program Run Disable PRD ModeProgram Port, Pinouts, and Signals Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Working With the Configuration DIP SwitchNI-2000 Port Assignments Modes and Front Panel LED Blink PatternsPort Assignments and Functionality Modes and LED Blink PatternsWiring Guidelines NI-3000 & NI-4000 @ 900 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-2000 @ 700 mAWiring a Power Connection Preparing Captive WiresUsing the 4-Pin Mini-Phoenix Connector For Data and Power RS-232 RS-422 RS-485 DB9 Device Port Connections and WiringRJ-45 Pinout Information EIA/TIA 568 B ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications ICSNet RJ-45 SignalsRelay Connections ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring ICSHub OUT Pinouts and SignalsPort Wiring Specifications NI-4000 and NI-3000 Input/Output I/O Port Connections and WiringPort Wiring Specifications NI-2000 Signal Function IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only IR/Serial Connector Wiring Specifications per PortEthernet LEDs Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Pin Signals Connections Pairing ColorEthernet Port Descriptions Ethernet Ports Used By the Integrated ControllerPort type Description Standard Port # Page It’s Your World Take Control