AMX NXI-x000 Series manual Install screws Bracket Rack Mounting Holes

Page 24

Installation and Upgrading

Install screws

Bracket

Rack

Mounting Holes

FIG. 5 Mounting Integrated Controller into an equipment rack

3.Thread the cables through the opening in the equipment rack. Allow for enough slack in the cables to accommodate for movement during the installation process.

4.Reconnect all cables to their appropriate source/terminal locations. Refer to theConnections and Wiring section on page 19 for more detailed wiring and connection information.

Verify that the terminal end of the power cable is not connected to the a power supply before plugging in the 2-pin power connector.

To prevent repetition of the installation, test the incoming wiring by connecting the Controller’s connectors to their terminal locations and applying power. Verify that the unit is receiving power and functioning properly. Disconnect the terminal end of the power cable from the connected 12 VDC-compliant power supply.

5.Slide the unit into the rack until the attachment holes, along both sides, align to their corresponding locations on the mounting brackets, as shown in FIG. 5.

6.Secure the AC-RK to the rack by using the four #10-32 screws (80-0186) and four #10 washers (80-0342) supplied in the kit.

7.Apply power to the unit to complete the installation.

20	NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Image 24

Contents NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NetLinx Integrated Master Controller Features IntroductionNI-2000 Specifications RearNI-2000 Specifications Rear Panel ConnectorsFront Panel Components Surge damage NI-2000 Specifications NI-3000 Specifications NI-3000 NetLinx Integrated Controller front viewNI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 Specifications NI-4000 NetLinx Integrated Controller front viewNI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installation and Upgrading Installing NetLinx Control Cards NI-4000 OnlySetting the NetLinx Control Card Addresses NI-4000 Only DevicePortSystem DPSPosition Compact Flash Upgrades Optional Compact Flash UpgradesRemoving NetLinx Control Cards NI-4000 Only Product Name DescriptionInstallation of Compact Flash Upgrades Installing Into An Equipment Rack Closing and Securing the Outer HousingInstall screws Bracket Rack Mounting Holes Setting the Configuration DIP Switch for the Program Port Baud Rate SettingsProgram Run Disable PRD Mode Baud Rate Settings on the Configuration DIP SwitchSetting the CardFrame DIP Switch NI-4000 Only Program Port Connections and WiringWorking With the Configuration DIP Switch Program Port, Pinouts, and SignalsModes and Front Panel LED Blink Patterns Port Assignments and FunctionalityModes and LED Blink Patterns NI-2000 Port AssignmentsWiring Guidelines Wiring length guidelinesWiring Guidelines NI-2000 @ 700 mA Wiring Guidelines NI-3000 & NI-4000 @ 900 mAPreparing Captive Wires Wiring a Power ConnectionUsing the 4-Pin Mini-Phoenix Connector For Data and Power DB9 Device Port Connections and Wiring RS-232 RS-422 RS-485ICSNet Port Connections and Wiring RS-232/422/485 Device Port Wiring SpecificationsICSNet RJ-45 Signals RJ-45 Pinout Information EIA/TIA 568 BICSHub OUT Port Connections and Wiring Relay Port Connections and WiringICSHub OUT Pinouts and Signals Relay ConnectionsInput/Output I/O Port Connections and Wiring Port Wiring Specifications NI-4000 and NI-3000Port Wiring Specifications NI-2000 IR/Serial Port Connections and Wiring NetLinx Control Card Slot Connector NI-4000 onlyIR/Serial Connector Wiring Specifications per Port Signal FunctionEthernet/RJ-45 Port Connections and Wiring Ethernet RJ-45 Pinouts and SignalsPin Signals Connections Pairing Color Ethernet LEDsEthernet Ports Used By the Integrated Controller Ethernet Port DescriptionsPort type Description Standard Port # Page It’s Your World Take Control