Allied Telesis AT-9000/12POE, AT-9000/28POE manual Management Methods

Page 18

AT-9000 Gigabit Ethernet Switch Installation Guide

Port LEDs

Installation Options

MAC Address Table

Management

Software and

Interfaces

Management Methods

Here are the port LEDs:

Duplex mode and link/activity LEDs for the twisted-pair ports

PoE status for the twisted-pair ports on AT-9000/12POE and AT-9000/28POE switches

Link/activity LEDs for the SFP slots

ecoFriendly button turns off the LEDs to conserve electricity

Note

For more detail on the above LEDs and other LEDs on the switches, refer to “LEDs” on page 37.

Here are the installation options:

19 inch equipment rack

Desk or tabletop

Here are the basic features of the MAC address tables of the switches:

Storage capacity of 16,000 MAC address entries

Automatic learning and aging

Here are the management software and management interfaces:

AlliedWare Plus Management Software

Command line interface

Web browser interface

Here are the methods for managing the switches:

Local management through the Console port

Remote Telnet and Secure Shell management

Remote HTTP and HTTPS web browser management

SNMPv1, v2c, and v3

18

Image 18
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Snmp Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis AT-9000 Gigabit Ethernet Switch Installation Guide Overview ChapterSwitch Models and Features AT-9000 Series ModelsPower over Ethernet RS-232 Console PortManagement Methods AT-9000 Series Gigabit Ethernet Switches AT-9000/12POE SwitchAT-9000/12POE Switch Front and Rear Panels AT-9000/28 Switch SFP/RJ45AT-9000/28POE Switch AT-9000/28POE Switch Front and Rear PanelsAT-9000/28SP Switch AT-9000/28SP Switch Front and Rear PanelsAT-9000/52 Switch AT-9000/52 Switch Front and Rear Panels10/100/1000Base-T Twisted-Pair Ports Wiring Configuration Maximum Distance 10Mbps 100Mbps 1000Mbps Cable Type Non PoE PoE+ Power Over Ethernet Powered Device Classes Port Prioritization Wiring Implementation SFP Slots 10/100/1000 SFP Slot Base-T PortOverview Combo Ports Overview Console Port Mode LED Select Button LEDsLink LED Mode SFP LINK/ACT LEDs EcoFriendly Button Front Panel ecoFriendly ButtonPower Supplies Power Connectors AT-9000 Gigabit Ethernet Switch Installation Guide Beginning the Installation Installation Procedures Reviewing Safety Precautions AT-9000 Gigabit Ethernet Switch Installation Guide Beginning the Installation AT-9000 Gigabit Ethernet Switch Installation Guide Selecting a Site Unpacking the Switch Installing the Switch on a Table or Rack Installing the Switch on a Table or Desktop Installing the Switch in a Rack Attaching Brackets for Rack Mounting Mounting the Switch in a Rack AT-9000 Gigabit Ethernet Switch Installation Guide Cabling the Networking Ports AT-9000 Gigabit Ethernet Switch Installation Guide Powering On the Switch Applying AC Power Connecting the AC Power CordPowering On the Switch Starting a Local Management Session Powering On the Switch Management Methods Local Management Telnet ManagementSecure Shell Management Web Browser Management AT-9000 Gigabit Ethernet Switch Installation Guide Adding a Management IP Address Awplus enable Troubleshooting Power LED Is Off Twisted-Pair Port Link LED Is Off AT-9000 Gigabit Ethernet Switch Installation Guide Cannot Establish a Local Out-of-Band Management Session All Port LEDs Are Off Power Over Ethernet Fiber Optic Transceivers Slow Performance Between Switch and Host Device AT-9000 Gigabit Ethernet Switch Installation Guide Technical Specifications Physical SpecificationsAppendix a Environmental Specifications Power SpecificationsSafety and Electromagnetic Emissions Certifications Quality and ReliabilityCompliance Standards 10/100/1000Base-T Twisted-Pair Port Connectors Pin SignalPin Pair Signal Console Port PinoutsAT-9000 Gigabit Ethernet Switch Installation Guide