Allied Telesis AT-9000/28POE, AT-9000/12POE manual Reviewing Safety Precautions

Page 47

Chapter 2: Beginning the Installation

Reviewing Safety Precautions

Review the following safety precautions before you begin to install the switch or any of its components.

Note

The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” posted on the Allied Telesis website at www.alliedtelesis.com.

Note

Refer to the data sheet about an SFP module at www.alliedtelesis.com to determine whether it is a Class 1 LED or a Class 1 Laser product.

Warning

Class 1 Laser product. L1

Warning

Do not stare into the laser beam. L2

Warning

Class 1 LED product. L3

Warning

To prevent electric shock, do not remove the cover. There are no user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1

47

Image 47
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Snmp Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis AT-9000 Gigabit Ethernet Switch Installation Guide Chapter OverviewAT-9000 Series Models Switch Models and FeaturesRS-232 Console Port Power over EthernetManagement Methods AT-9000/12POE Switch AT-9000 Series Gigabit Ethernet SwitchesAT-9000/12POE Switch Front and Rear Panels SFP/RJ45 AT-9000/28 SwitchAT-9000/28POE Switch Front and Rear Panels AT-9000/28POE SwitchAT-9000/28SP Switch Front and Rear Panels AT-9000/28SP SwitchAT-9000/52 Switch Front and Rear Panels AT-9000/52 Switch10/100/1000Base-T Twisted-Pair Ports Wiring Configuration Maximum Distance 10Mbps 100Mbps 1000Mbps Cable Type Non PoE PoE+ Power Over Ethernet Powered Device Classes Port Prioritization Wiring Implementation 10/100/1000 SFP Slot Base-T Port SFP SlotsOverview Combo Ports Overview Console Port LEDs Mode LED Select ButtonLink LED Mode SFP LINK/ACT LEDs Front Panel ecoFriendly Button EcoFriendly ButtonPower Supplies Power Connectors AT-9000 Gigabit Ethernet Switch Installation Guide Beginning the Installation Installation Procedures Reviewing Safety Precautions AT-9000 Gigabit Ethernet Switch Installation Guide Beginning the Installation AT-9000 Gigabit Ethernet Switch Installation Guide Selecting a Site Unpacking the Switch Installing the Switch on a Table or Rack Installing the Switch on a Table or Desktop Installing the Switch in a Rack Attaching Brackets for Rack Mounting Mounting the Switch in a Rack AT-9000 Gigabit Ethernet Switch Installation Guide Cabling the Networking Ports AT-9000 Gigabit Ethernet Switch Installation Guide Powering On the Switch Connecting the AC Power Cord Applying AC PowerPowering On the Switch Starting a Local Management Session Powering On the Switch Local Management Telnet Management Management MethodsSecure Shell Management Web Browser Management AT-9000 Gigabit Ethernet Switch Installation Guide Adding a Management IP Address Awplus enable Troubleshooting Power LED Is Off Twisted-Pair Port Link LED Is Off AT-9000 Gigabit Ethernet Switch Installation Guide Cannot Establish a Local Out-of-Band Management Session All Port LEDs Are Off Power Over Ethernet Fiber Optic Transceivers Slow Performance Between Switch and Host Device AT-9000 Gigabit Ethernet Switch Installation Guide Appendix a Technical SpecificationsPhysical Specifications Power Specifications Environmental SpecificationsCompliance Standards Safety and Electromagnetic Emissions CertificationsQuality and Reliability Pin Signal 10/100/1000Base-T Twisted-Pair Port ConnectorsConsole Port Pinouts Pin Pair SignalAT-9000 Gigabit Ethernet Switch Installation Guide