Linksys SFE2010P manual Connecting the Cables, Wall-Mount Placement

Page 11

Connecting Devices

Connecting the Cables

Wall-Mount Placement

1.On one of the side corners, remove the four front screws on of the Ethernet switch. Retain the screws for re-installation.

NOTE: The Ethernet switch, shown below, is mounted with the ports located on top. When the switch is mounted to a wall, the ports can be oriented in any direction.

2.Place one of the supplied spacers on the side of the Ethernet switch so the four holes align to the screw holes.

3.Place a rack mount bracket next to the spacer and reinstall the four screws (removed in step 1). The wall mount brackets should point towards the bottom of the Ethernet switch.

4.Repeat steps 1 through 3 for the other corners of the Ethernet switch.

5.Attach the Ethernet switch to a wall with appropriate screws (not supplied). CAUTION: Ensure that the Ethernet switch is securely attached to the wall.

Connecting the Cables

To connect network devices to the Ethernet switch, follow these instructions:

1.For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the numbered ports on the Ethernet switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the uplink ports on the Ethernet switch.

NOTE: If connecting an Ethernet switch to an SVR3000 router, connect it to a Cascade port on the SVR3000.

2.Connect the other end to a PC or other network device.

3.Repeat steps 2 and 3 to connect additional devices.

4.If you are using the mini-GBIC port, then insert the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the documentation supplied with the mini-GBIC module.

SFE2010/SFE2010P Administration Guide

8

Image 11

Contents Port 10/100 Ethernet Switch Table of Contents Contacts What’s in this User Guide? WelcomeSFE2010/P Front Panel Getting to Know the SFE2010/SFE2010PGetting to Know the SFE2010/SFE2010P SFE2010/P Back Panel Maximum Cabling Distances Sample Network ConfigurationDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Wall-Mount Placement Connecting the CablesConnecting Devices Using Menus in the Web-Based Utility Connecting to the Switch with the Web-Based UtilityViewing On-line Help Connecting to Your Switch with HyperTerminal Using the ConsoleUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console System Configuration Using the Switch Main MenuTo open this menu System InformationTo open this screen General Information VersionsTo change the system contact, system name, and location Management SettingsTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration To change the time-out setting SSH ConfigurationTo change SSH Server settings SSH Server ConfigurationTo change SSH Crypto Key Generation settings To generate the crypto key Username & Password SettingsTo change User & Password settings Security SettingsTo edit and execute a certificate SSL Generate CertificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Vlan Management Default Vlan SetupTo edit the Vlan ID IP ConfigurationIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings To edit the IPv6 default gateway settings IPv6 Default GatewayTo open the screen Http ConfigurationHttps Configuration To change the Http settingsTo change Https settings Network ConfigurationTo begin the ping test To change the IP addressPing IPv6 To begin the trace route test TraceRoute IPv6 File Management Upgrade / Backup IPv4To download a file from the specified location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To enter the IPv6 Upgrade/Backup file name and locationActive Image To enter the active image settingsTo restore system default settings Restore System Default SettingsReset to Factory Settings Reboot SystemPort Status Stack ConfigurationPoE Status Port StatusPort Settings Port ConfigurationTo configure the ports PoE SettingsTo configure the PoE settings System Mode Layer 2 / Layer 3 SelectionHelp To edit the system mode or stacking modeLogout EU Contacts US/Canada ContactsCustomer Site Survey Yes Exclusions and Limitations Limited WarrantyObtaining Warranty Service Obtaining Warranty Service Technical SupportEC Declaration of Conformity Europe Industry Canada StatementSpecifications Radius Vlan EMC 080312A-LB