Linksys SFE2010P manual Vlan

Page 65

Access Control	ACLs - Drop or Rate Limit based on:
	Source and Destination MAC-based
	Source and Destination IP address
	Protocol
	Port
	VLAN
	DSCP/IP Precedence
	TCP/UDP Source and Destination ports
	802.1p priority
	Ethernet Type
	ICMP packets
	IGMP packets
	DHCP Snooping
	ARP Inspection
	IP Source Address Guard
	Up to 1018 rules

Link Aggregation	Link Aggregation using IEEE 802.3ad LACP
	Up to 8 ports in up to 8 groups

Storm Control	Broadcast, Multicast and Unknown Unicast

DOS prevention	DOS Attack prevention

Spanning Tree	IEEE 802.1D Spanning Tree, IEEE 802.1w Rapid Spanning Tree, IEEE 802.1s Multiple
	Spanning Tree, Fast Linkover

IGMP Snooping	IGMP (v1/v2) snooping limits bandwidth-intensive video traffic to only the
	requestors. Support 256 multicast groups.

Power Redundancy	Connection to RPSU for power redundancy

QoS	Priority levels: 4 Hardware queues
	Scheduling: Priority Queuing and Weighted Round Robin (WRR)
	Class of Service:
	•	Port-based
	• 802.1p VLAN priority based
	• IPv4/v6 IP Precedence/TOS/DSCP based
	•	Diffserv
	• Classification and Remarking ACLs
	Rate Limiting:
	•	Ingress policer
	•	Egress rate control
	•	Per VLAN
	Statistics: 16 meters

Standards	802.3 10BASE-T Ethernet, 802.3u 100BASE-TX Fast Ethernet, 802.3ab 1000BASE-T
	Gigabit Ethernet, 802.3z Gigabit Ethernet, 802.3x Flow Control, 802.3 ad LACP,
	802.1d STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port
	Access Authentication

Certifications	UL (UL 60950), CSA (CSA 22.2), CE mark, FCC Part 15 (CFR 47) Class A

Regulatory Compliance	Products with the CE Marking indicate compliance with the 89/336/EEC and 73/
	23/EEC directives, which include the safety and EMC standards listed below.

SFE2010/SFE2010P Administration Guide

62

Image 65

Contents Port 10/100 Ethernet Switch Table of Contents Contacts What’s in this User Guide? WelcomeSFE2010/P Front Panel Getting to Know the SFE2010/SFE2010PGetting to Know the SFE2010/SFE2010P SFE2010/P Back Panel Maximum Cabling Distances Sample Network ConfigurationDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Wall-Mount Placement Connecting the CablesConnecting Devices Using Menus in the Web-Based Utility Connecting to the Switch with the Web-Based UtilityViewing On-line Help Connecting to Your Switch with HyperTerminal Using the ConsoleUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console System Configuration Using the Switch Main MenuTo open this menu System InformationTo open this screen General Information VersionsTo change the system contact, system name, and location Management SettingsTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration To change the time-out setting SSH ConfigurationTo change SSH Server settings SSH Server ConfigurationTo change SSH Crypto Key Generation settings To generate the crypto key Username & Password SettingsTo change User & Password settings Security SettingsTo edit and execute a certificate SSL Generate CertificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Vlan Management Default Vlan SetupTo edit the Vlan ID IP ConfigurationIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings To edit the IPv6 default gateway settings IPv6 Default GatewayHttps Configuration Http ConfigurationTo change the Http settings To open the screenTo change Https settings Network ConfigurationTo begin the ping test To change the IP addressPing IPv6 To begin the trace route test TraceRoute IPv6 File Management Upgrade / Backup IPv4To enter the IPv4 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv6 Upgrade/Backup file name and location To download a file from the specified locationActive Image To enter the active image settingsReset to Factory Settings Restore System Default SettingsReboot System To restore system default settingsPort Status Stack ConfigurationPoE Status Port StatusPort Settings Port ConfigurationTo configure the ports PoE SettingsTo configure the PoE settings System Mode Layer 2 / Layer 3 SelectionHelp To edit the system mode or stacking modeLogout EU Contacts US/Canada ContactsCustomer Site Survey Yes Exclusions and Limitations Limited WarrantyObtaining Warranty Service Obtaining Warranty Service Technical SupportEC Declaration of Conformity Europe Industry Canada StatementSpecifications Radius Vlan EMC 080312A-LB