Linksys SGE2010P manual Network Configuration, To change Https settings

Page 38

Using the Console

System Configuration

To open the screen:

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 6. IP Configuration.

3.From the IP Configuration menu, select 4. HTTPS Configuration.

To change HTTPS settings:

1.Select Edit, and then make your changes.

2.Press the Esc key to move the cursor to the Action list.

3.Select Save to save your changes.

4.When the Operation complete message appears, press the Esc key to move the cursor to the Action list.

Network Configuration

The Network Configuration screen provides access to screens where you can execute ping tests and traceroute tests for IPv4 and IPv6 addresses.

1.Ping IPv4 (see page 36)

2.Ping IPv6 (see page 37)

3.TraceRoute IPv4 (see page 38)

4.TraceRoute IPv6 (see page 39)

0.Back (Select to return to the previous menu.)

To open the screen:

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 6. IP Configuration.

3.From the IP Configuration menu, select 5. Network Configuration.

SGE2010/SGE2010P Administration Guide

35

Image 38
Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console Using the Switch Main Menu System ConfigurationTo open this menu System InformationTo open this screen Versions General InformationManagement Settings To change the system contact, system name, and locationTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsTo change the Http settings Http ConfigurationHttps Configuration To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementTo enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageReboot System Restore System Default SettingsReset to Factory Settings To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB