Linksys SGE2010P manual Specifications

Page 62

E

Specifications

Model

Ports

•SGE2010 48-port 10/100/1000 Ethernet Switch

•SGE2010P 48-port 10/100/1000 Ethernet Switch with PoE

•IEEE 802.3af PoE on delivered over any of the 48 10/100 ports

•Power budget allows for max power of 15.4W to an Ethernet port, with 360W available to all ports on regular AC, and 280W available on redundant power supply

48 RJ-45 connectors for 10BASE-T/100BASE-TX/1000Base-T with 4 Gigabit combo ports shared between mini-GBIC ports

Console port

Auto MDI/MDI-X

Autonegotiate/Manual setting

RPS port for connecting to Redundant Power Supply unit

Cabling Type	UTP CAT 5 or better for 10BASE-T/100BASE-TX, UTP CAT 5e or better for
	1000BASE-T

Switching Capacity	96 Gig non-blocking

Forwarding Capacity	71.4M packets per second (64-byte packets)

LEDs

Stack Operation

Power, Fan, Link/Act, PoE, Speed, RPS, Master, Stack ID 1 - 8

•Up to 192 ports in a stack

•Hot Insertion and removal

•Ring and Chain stacking options

•Master and Backup master for resilient stack control

•Auto-numbering or manual configuration of units in stack

Buttons	Reset Button

Layer 2 options	8K
	256 active VLANs (4096 range)
	Port-based and 802.1Q Tag-based VLANs
	Protocol-based VLAN
	Management VLAN
	Multicast TV VLAN
	Private VLAN Edge (PVE)
	GVRP
	Head of line blocking prevention

Layer 3 options	Static Routing
	CIDR (Classless Interdomain Routing)
	60 Static Routes
	IPv4 and IPv6
	Forwarding in silicon - Wirespeed forwarding of layer 3 traffic

SGE2010/SGE2010P Administration Guide

59

Image 62

Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console Using the Switch Main Menu System ConfigurationTo open this menu System InformationTo open this screen Versions General InformationManagement Settings To change the system contact, system name, and locationTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsTo change the Http settings Http ConfigurationHttps Configuration To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementTo enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageReboot System Restore System Default SettingsReset to Factory Settings To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB