Linksys SGE2010P manual Yes

Page 58

How many users are at your site?

 

 

Phone number and location of the telephone

 

 

nearest to the Linksys equipment

 

 

Access Procedures

 

 

Specify room access procedures (for example,

 

 

must visiting personnel be escorted by

 

 

customer personnel?).

 

 

Security/Safety Procedures

 

 

Specify any special security/safety

 

 

procedures, such as the need for safety

 

 

glasses, safety shoes, and the location(s) of

 

 

hardhat areas.

 

 

Site Coordinator

 

 

Specify the name and phone number of the

 

 

site coordinator responsible for ensuring that

 

 

the site is adequately prepared for the

 

 

installation of the Cisco equipment.

 

 

Name:

 

 

Phone:

 

 

Network/Bandwidth

 

 

What is the downlink and uplink speed of

 

 

your broadband connection?

 

 

Uplink speed (must be greater than 768

 

 

Kbps):

 

 

Downlink speed (must be greater than 768

 

 

Kbps):

 

 

Does your network use a firewall?

￿ Yes

￿ No

SGE2010/SGE2010P Administration Guide

55

Image 58
Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesPlacement Options Before You Install the SwitchDesktop Placement Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Logging On to the Console Connecting to the Switch with TelnetSelecting Menu Options and Actions Using the Switch Main Menu System ConfigurationTo open this screen System InformationTo open this menu Versions General InformationManagement Settings To change the system contact, system name, and locationTelnet Configuration Serial Port ConfigurationTo change the baud rate of the serial port SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateTo disable the active management access profile Disable Active Management Access ProfileShow Certificate Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To edit the IPv4 address settings IPv6 Address ConfigurationTo renew Dhcp To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsTo change the Http settings Http ConfigurationHttps Configuration To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementTo enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageReboot System Restore System Default SettingsReset to Factory Settings To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB