Linksys Complete Manual for Efficient Console Management of SGE2010P

Page 44

Using the Console

System Configuration

To enter the IPv4 Upgrade/Backup file name and location:

1.Select Edit, and then make the changes. Press the Tab key to move the cursor from one field to the next.

NOTE: Specify the source and destination of the file, the file name, and the IPv4 address of the file server where the upgrade file is stored,

2.Press the Esc key to move the cursor to the Action list.

To download a file from the specified location:

3.Verify that the file name and location are correct.

4.Select Execute.

5.When the Operation complete message appears, press the Esc key to move the cursor to the Action list.

Upgrade / Backup IPv6

You can use the Upgrade/Backup IPv6 screen to download files from an IPv6 address.

To open this screen:

1.From the Switch Main Menu, select 1. System Configuration.

2.From the System Configuration Menu, select 7. File Management.

3.From the File Management Menu, select 2. IPv6 Upgrade/Backup.

To enter the IPv6 Upgrade/Backup file name and location:

1.Select Edit, and then make the changes. Press the Tab key to move the cursor from one field to the next.

NOTE: Specify the source and destination of the file, the file name, and the IPv6 address of the file server where the upgrade file is stored. For an IPv6 address, you also must specify the interface type and ID.

2.Press the Esc key to move the cursor to the Action list.

SGE2010/SGE2010P Administration Guide

41

Image 44
Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console Using the Switch Main Menu System ConfigurationTo open this menu System InformationTo open this screen Versions General InformationManagement Settings To change the system contact, system name, and locationTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsHttp Configuration Https ConfigurationTo change the Http settings To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementUpgrade / Backup IPv6 To enter the IPv4 Upgrade/Backup file name and locationTo enter the IPv6 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageRestore System Default Settings Reset to Factory SettingsReboot System To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB