Linksys SGE2010P manual Vlan

Page 64

Access Control	ACLs - Drop or Rate Limit based on:
	Source and Destination MAC-based
	Source and Destination IP address
	Protocol
	Port
	VLAN
	DSCP/IP Precedence
	TCP/UDP Source and Destination ports
	802.1p priority
	Ethernet Type
	ICMP packets
	IGMP packets
	DHCP Snooping
	ARP Inspection
	IP Source Address Guard
	Up to 1018 rules

Link Aggregation	Link Aggregation using IEEE 802.3ad LACP
	Up to 8 ports in up to 8 groups

Storm Control	Broadcast, Multicast and Unknown Unicast

DOS prevention	DOS Attack prevention

Spanning Tree	IEEE 802.1D Spanning Tree, IEEE 802.1w Rapid Spanning Tree, IEEE 802.1s Multiple
	Spanning Tree, Fast Linkover

IGMP Snooping	IGMP (v1/v2) snooping limits bandwidth-intensive video traffic to only the
	requestors. Support 256 multicast groups.

Power Redundancy	Connection to RPSU for power redundancy

QoS	Priority levels: 4 Hardware queues
	Scheduling: Priority Queuing and Weighted Round Robin (WRR)
	Class of Service:
	•	Port-based
	• 802.1p VLAN priority based
	• IPv4/v6 IP Precedence/TOS/DSCP based
	•	Diffserv
	• Classification and Remarking ACLs
	Rate Limiting:
	•	Ingress policer
	•	Egress rate control
	•	Per VLAN
	Statistics: 16 meters

Standards	802.3 10BASE-T Ethernet, 802.3u 100BASE-TX Fast Ethernet, 802.3ab 1000BASE-T
	Gigabit Ethernet, 802.3z Gigabit Ethernet, 802.3x Flow Control, 802.3 ad LACP,
	802.1d STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port
	Access Authentication

Certifications	UL (UL 60950), CSA (CSA 22.2), CE mark, FCC Part 15 (CFR 47) Class A

Regulatory Compliance	Products with the CE Marking indicate compliance with the 89/336/EEC and 73/
	23/EEC directives, which include the safety and EMC standards listed below.

SGE2010/SGE2010P Administration Guide

61

Image 64

Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesPlacement Options Before You Install the SwitchDesktop Placement Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Logging On to the Console Connecting to the Switch with TelnetSelecting Menu Options and Actions Using the Switch Main Menu System ConfigurationTo open this screen System InformationTo open this menu Versions General InformationManagement Settings To change the system contact, system name, and locationTelnet Configuration Serial Port ConfigurationTo change the baud rate of the serial port SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateTo disable the active management access profile Disable Active Management Access ProfileShow Certificate Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To edit the IPv4 address settings IPv6 Address ConfigurationTo renew Dhcp To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsHttp Configuration Https ConfigurationTo change the Http settings To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementUpgrade / Backup IPv6 To enter the IPv4 Upgrade/Backup file name and locationTo enter the IPv6 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageRestore System Default Settings Reset to Factory SettingsReboot System To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB