Linksys SGE2010P manual PoE Settings, To configure the ports

Page 50

Using the Console

Port Configuration

To configure the ports:

1.Select Edit.

2.Proceed as needed:

a.Press the down arrow key to scroll down through the list of ports.

b.Press the right arrow key to move the cursor from one field to the next within a row.

c.To change a setting, move the cursor to the field, and then press the Space Bar until the desired setting appears.

Field

Settings

 

 

 

 

Enable

Enable or Disable

 

 

Auto Neg.

On or Off

 

 

Spd/Dpx

Auto, 10H, 100H, 10F, 100F, 1000F

 

 

Flow Ctrl

Auto, On or Off

 

 

3.Press the Esc key to move the cursor to the Action list.

4.Select Save to save your settings

5.When the Operation complete message appears, press the Esc key to move the cursor to the Action list.

PoE Settings

You can use the PoE Settings screen to specify the priority and PoE settings for each port. You can use the up or down arrow keys to scroll through all the ports on the Ethernet switch.

To open this screen:

1.From the Switch Main Menu, press 3. Port Configuration.

2.From the Port Status Menu, press 2. Poe Settings.

SGE2010/SGE2010P Administration Guide

47

Image 50
Contents Port 10/100/1000 Ethernet Switch Table of Contents Contacts Introduction What’s in this User Guide?Getting to Know the SGE2010/SGE2010P SGE2010/P Front PanelGetting to Know the SGE2010/SGE2010P SGE2010/P Back PanelSample Network Configuration Maximum Cabling DistancesDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Connecting the Cables Wall-Mount PlacementConnecting Devices to the SGE2010/SGE2010P Using the Console Connecting to Your Switch with HyperTerminalUsing the Console Set the serial port settings as follows Selecting Menu Options and Actions Connecting to the Switch with TelnetLogging On to the Console Using the Switch Main Menu System ConfigurationTo open this menu System InformationTo open this screen Versions General InformationManagement Settings To change the system contact, system name, and locationTo change the baud rate of the serial port Serial Port ConfigurationTelnet Configuration SSH Configuration To change the time-out settingSSH Server Configuration To change SSH Server settingsTo change SSH Crypto Key Generation settings Username & Password Settings To generate the crypto keySecurity Settings To change User & Password settingsSSL Generate Certificate To edit and execute a certificateShow Certificate Disable Active Management Access ProfileTo disable the active management access profile Default Vlan Setup Vlan ManagementIP Configuration To edit the Vlan IDIPv4 Address Configuration To renew Dhcp IPv6 Address ConfigurationTo edit the IPv4 address settings To edit the IPv6 interface settings To edit the IPv6 address settings IPv6 Address Table To edit the Isatap tunnel settings IPv6 Default Gateway To edit the IPv6 default gateway settingsTo change the Http settings Http ConfigurationHttps Configuration To open the screenNetwork Configuration To change Https settingsTo change the IP address To begin the ping testPing IPv6 To begin the trace route test TraceRoute IPv6 Upgrade / Backup IPv4 File ManagementTo enter the IPv6 Upgrade/Backup file name and location Upgrade / Backup IPv6To enter the IPv4 Upgrade/Backup file name and location To download a file from the specified locationTo enter the active image settings Active ImageReboot System Restore System Default SettingsReset to Factory Settings To restore system default settingsStack Configuration Port StatusPort Status PoE StatusPort Configuration Port SettingsPoE Settings To configure the portsSystem Mode Layer 2 / Layer 3 Selection To configure the PoE settingsTo edit the system mode or stacking mode HelpLogout Connecting to the Switch with the Web-Based Utility Using Menus in the Web-Based UtilityViewing On-line Help US/Canada Contacts EU ContactsCustomer Site Survey Yes Limited Warranty Exclusions and LimitationsObtaining Warranty Service Technical Support Obtaining Warranty ServiceIndustry Canada Statement EC Declaration of Conformity EuropeSpecifications Radius Vlan EMC 080312A-LB