Linksys SLM224P, SLM248P, SLM248G Hardware Installation, Desktop Placement, Rack-Mount Placement

Page 14

Chapter 3

Installation

Desktop Placement

•Attach the rubber feet to the recessed areas on the bottom of the Switch.

•Place the Switch on a desktop near an AC power source.

•Keep enough ventilation space for the switch and check the environmental restrictions mentioned in the Specifications Appendix as you are placing the Switch.

•Connect the Switch to network devices according to the Hardware Installation instructions below.

Attaching the Switch’s Rubber Feet

Rack-Mount Placement

When rack-mounting the Switch, please observe the following guidelines

•Elevated Operating Ambient  If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

•Reduced Air Flow  Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

•Mechanical Loading  Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

•Circuit Overloading  Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

•Reliable Earthing  Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

To rack-mount the Switch in any standard 19-inch wide, 1U high rack, follow the instructions described below.

1.Place the Switch on a hard flat surface with the front panel facing you.

2.Attach a rack–mount bracket to one side of the Switch with the supplied screws and secure the bracket tightly.

Attaching the Brackets

3.Follow the same steps to attach the other bracket to the opposite side.

4.After the brackets are attached to the Switch, use suitable screws to securely attach the brackets to any standard 19-inch rack.

Mounting in Rack

5.Connect the Switch to network devices according to the Hardware Installation instructions below.

Hardware Installation

To connect network devices to the Switch, follow these instructions:

1.Make sure all the devices you will connect to the Switch are powered off.

2.For a 10/100 Mbps device:

•All models: Connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch.

Business Series Smart Gigabit Ethernet Switch

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Business Series Smart Gigabit Ethernet Switch Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Table of Contents Appendix E Contact Information Appendix B Glossary Appendix C SpecificationsAppendix D Warranty and Regulatory Information Chapter Introduction IntroductionSLM2048 Chapter Product OverviewProduct Overview Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Pre-Installation Considerations Chapter InstallationInstallation Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement Uplinking the Switch WithSetup Summary Chapter Configuration Using Web-based UtilitySetup System Information Setup Network SettingsDevice Information IdentificationLocal Time Setup TimeIP Configuration Daylight SavingPort Management Port Management Port SettingsPort Configuration Port Management Link Aggregation LAG Configuration Global Parameter Port Management PoE Power SettingsPort Management Lacp Port PriorityVlan Management Create Vlan Vlan Management Port SettingsVlan Management Vlan Management Port to VlanJoin Vlan to Port Port The number of the port being configuredVlan Management Vlan to Port Interface StatisticsStatistics Interface Statistics Ethernet-likeSecurity Security 802.1x SettingsSetting Timer ParametersSecurity Port Security IP Address Enter the IP address to be allowed Security IP Access ListSecurity Storm Control Broadcast Only Counts only Broadcast trafficSecurity Radius CoS Default QoS CoS SettingsCoS Settings QoSQoS Basic Mode QoS Queue SettingsQoS Dscp Settings Spanning Tree STP Status Global SettingSpanning Tree Spanning Tree Global STPSpeed Displays the speed at which the port is operating Spanning Tree STP Port SettingsBridge Settings Multicast Igmp Snooping Vlan Igmp SettingsMulticast Multicast Bridge MulticastMulticast Bridge Multicast Forward All User Authentication AdminAdmin User Authentication Local User EditQuery Admin Static AddressAdmin Dynamic Address Secure The entry is defined for locked portsAdmin Port Mirroring Admin Save ConfigurationAdmin Factory Default Admin Firmware UpgradeAdmin Reboot Click the Reboot button, then click OK to confirmAdmin Flash Logs Admin LoggingAdmin Memory Logs Logout If you select Yes, a confirmation screen appearsFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Appendix B Glossary GlossaryGlossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix B SLM2024/SLM2048 Appendix C SpecificationsSpecifications Buttons Reset Cabling Type UTP CAT 5 or better for Power Internal Power CertificationConnectors for 10BASE-T UL, cUL, CE mark, CB83 lb 3.1 kg Unit Weight39 lb 2.9 kg 28 lb 3.3 kgAppendix D Warranty and Regulatory Information Limited WarrantyIndustry Canada Statement Safety NoticesFCC Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Appendix E Contact Information
Top Page Image Contents