Linksys SLM248G, SLM248P, SLM224P, SLM2024 manual Statistics Interface Statistics, Ethernet-like

Page 25

Chapter 4

Configuration Using the Web-based Utility

Statistics

The Statistics tab contains the Interface Statistics screen, which lets you display statistics for a specified interface.

Statistics > Interface Statistics

Statistics > Interface Statistics

This screen allows you to display statistics for the Ethernet port or LAG that you specify. You can also specify the rate at which the display will be refreshed.

Interface  To display statistics for an Ethernet port, select Port, then select the desired port from the drop-down menu. To display statistics for a LAG, select LAG and then select the desired LAG from the drop-down menu.

Refresh Rate  Select the rate at which to refresh the statistics display. The values are 15 sec, 30 sec, 60 sec, and No Refresh (default).

Interface

This section displays statistics for the packets transmitted and received on the selected interface.

Receive Statistics  Statistics on received packets

Total Bytes (Octets)  Displays the number of octets received on the selected interface.

Unicast Packets  Displays the number of Unicast packets received on the selected interface.

Multicast Packets  Displays the number of Multicast packets received on the selected interface.

Broadcast Packets  Displays the number of Broadcast packets received on the selected interface.

Packets with Errors  Displays the number of error packets received from the selected interface.

Transmit Statistics  Statistics on transmitted packets

Total Bytes (Octets)  Displays the number of octets transmitted from the selected interface.

Unicast Packets  Displays the number of Unicast packets transmitted from the selected interface.

Multicast Packets  Displays the number of Multicast packets transmitted from the selected interface.

Broadcast Packets  Displays the number of Broadcast packets transmitted from the selected interface.

Ethernet-like

This section displays the following statistics for the selected interface.

Frame Check Sequence (FCS) Errors  Displays the number of FCS errors received on the selected interface.

Single Collision Frames  Displays the number of single collision frames received on the selected interface.

Late Collisions  Displays the number of late collision frames received on the selected interface.

Oversize Packets  Displays the number of oversize packet errors on the selected interface.

Internal MAC Receive Errors  Displays the number of internal MAC received errors on the selected interface.

Received Pause Frames  Displays the number of received paused frames on the selected interface.

Transmitted Pause Frames  Displays the number of paused frames transmitted from the selected interface.

Clear Counters  Click the Clear Counters button to reset all the counters on this screen to zero.

Business Series Smart Gigabit Ethernet Switch

20

Image 25
Contents Business Series Smart Gigabit Ethernet Switch About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Table of Contents Appendix D Warranty and Regulatory Information Appendix B Glossary Appendix C SpecificationsAppendix E Contact Information Introduction Chapter IntroductionProduct Overview Chapter Product OverviewSLM2048 Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Installation Chapter InstallationPre-Installation Considerations Placement OptionsDesktop Placement Hardware InstallationRack-Mount Placement With Uplinking the SwitchSetup Chapter Configuration Using Web-based UtilitySetup Summary Device Information Setup Network SettingsSystem Information IdentificationIP Configuration Setup TimeLocal Time Daylight SavingPort Configuration Port Management Port SettingsPort Management Port Management Link Aggregation LAG Configuration Port Management Lacp Port Management PoE Power SettingsGlobal Parameter Port PriorityVlan Management Vlan Management Port SettingsVlan Management Create Vlan Vlan Management Port to VlanVlan Management Vlan to Port Port The number of the port being configuredJoin Vlan to Port Statistics Interface Statistics StatisticsInterface Ethernet-likeSetting Timer Security 802.1x SettingsSecurity ParametersSecurity Port Security Security Storm Control Security IP Access ListIP Address Enter the IP address to be allowed Broadcast Only Counts only Broadcast trafficSecurity Radius CoS Settings QoS CoS SettingsCoS Default QoSQoS Dscp Settings QoS Queue SettingsQoS Basic Mode Spanning Tree Global SettingSpanning Tree STP Status Spanning Tree Global STPBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Multicast Vlan Igmp SettingsMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Admin User Authentication AdminUser Authentication Local User EditAdmin Dynamic Address Admin Static AddressQuery Secure The entry is defined for locked portsAdmin Save Configuration Admin Port MirroringAdmin Reboot Admin Firmware UpgradeAdmin Factory Default Click the Reboot button, then click OK to confirmAdmin Memory Logs Admin LoggingAdmin Flash Logs If you select Yes, a confirmation screen appears LogoutGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Glossary Appendix B GlossaryGlossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix B Specifications Appendix C SpecificationsSLM2024/SLM2048 Connectors for 10BASE-T Power Internal Power CertificationButtons Reset Cabling Type UTP CAT 5 or better for UL, cUL, CE mark, CB39 lb 2.9 kg Unit Weight83 lb 3.1 kg 28 lb 3.3 kgLimited Warranty Appendix D Warranty and Regulatory InformationFCC Statement Safety NoticesIndustry Canada Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Contact Information Appendix E