Linksys SLM248G, SLM248P, SLM224P manual Chapter Product Overview, SLM2048, Back Panel, Front Panel

Page 7

Chapter 2

Chapter 2:

Product Overview

SLM2048

Front Panel

The Switch’s LEDs and ports are located on the front panel.

Front Panel of the SLM2048

SYSTEM  (Green)  Lights up to indicate that the Switch is powered on. Blinks while the Switch is performing a system self-test.

LNK/ACT (1-48) (Green) Lights up to indicate a functional 10/100/1000 Mbps network link through the corresponding port (1 through 48) with an attached device. Blinks to indicate that the Switch is actively sending or receiving data over that port.

Gigabit (1-48) (Amber) Lights up to indicate a functional 1000 Mbps connection on the corresponding port (1 through 48) with an attached device.

Reset  Press and hold the Reset Button for less than ten seconds to reboot the Switch. Press and hold the Reset Button for more than ten seconds to reset the Switch’s settings to the factory defaults.

Ethernet 1-48 The Switch is equipped with 48 auto-sensing, Ethernet network ports, which use RJ-45 connectors. The Fast Ethernet ports support network speeds of 10 Mbps, 100 Mbps, or 1000 Mbps. They can operate in half- and full- duplex modes. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10 Mbps, 100 Mbps, or 1000 Mbps), and adjust its speed and duplex accordingly.

Product Overview

miniGBIC (1-2) The miniGBIC (gigabit interface converter) port is a connection point for a miniGBIC expansion module, so the Switch can be uplinked via fiber to another switch. The MiniGBIC port provides a link to a high-speed network segment or individual workstation at speeds of up to 1000 Mbps.

To establish a Gigabit Ethernet connection using a miniGBIC port, you will need to install a MGBT1, MGBSX1, or MGBLH1 Gigabit expansion module and use Category 5e cabling or fiber optic cabling.

To establish a Fast Ethernet connection using a miniGBIC port, you will need to install a MFEFX1 (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP Transceiver and use fiber optic cabling.

NOTE:  On the SLM2048, MiniGBIC ports are shared with standard ports. If a miniGBIC port is used, then the shared standard port on the Switch cannot be used. The following table defines the shared port mapping of the SLM2048 Switch.

SLM2048 Shared Port Mapping

miniGBIC Port

Standard Port

 

 

miniGBIC 1

Port 24

miniGBIC 2

Port 48

 

 

Back Panel

The power port is located on the back panel of the Switch.

Back Panel of the SLM2048

POWER  The Power port is where you connect the AC power.

Business Series Smart Gigabit Ethernet Switch



Page 6 Page 8
Image 7
Page 6 Page 8
Contents Business Series Smart Gigabit Ethernet Switch Online Resources About This GuideAbout This Guide Icon DescriptionsTable of Contents Table of Contents Appendix D Warranty and Regulatory Information Appendix B Glossary Appendix C SpecificationsAppendix E Contact Information Introduction Chapter IntroductionBack Panel Chapter Product OverviewProduct Overview SLM2048SLM2024 SLM248G SLM248P SLM224G SLM224P Placement Options Chapter InstallationInstallation Pre-Installation ConsiderationsDesktop Placement Hardware InstallationRack-Mount Placement With Uplinking the SwitchSetup Chapter Configuration Using Web-based UtilitySetup Summary Identification Setup Network SettingsDevice Information System InformationDaylight Saving Setup TimeIP Configuration Local TimePort Configuration Port Management Port SettingsPort Management Port Management Link Aggregation LAG Configuration Port Priority Port Management PoE Power SettingsPort Management Lacp Global ParameterVlan Management Port to Vlan Vlan Management Port SettingsVlan Management Vlan Management Create VlanVlan Management Vlan to Port Port The number of the port being configuredJoin Vlan to Port Ethernet-like StatisticsStatistics Interface Statistics InterfaceParameters Security 802.1x SettingsSetting Timer SecuritySecurity Port Security Broadcast Only Counts only Broadcast traffic Security IP Access ListSecurity Storm Control IP Address Enter the IP address to be allowedSecurity Radius QoS QoS CoS SettingsCoS Settings CoS DefaultQoS Dscp Settings QoS Queue SettingsQoS Basic Mode Spanning Tree Global STP Global SettingSpanning Tree Spanning Tree STP StatusBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Multicast Bridge Multicast Vlan Igmp SettingsMulticast Multicast Igmp SnoopingMulticast Bridge Multicast Forward All Local User Edit AdminAdmin User Authentication User AuthenticationSecure The entry is defined for locked ports Admin Static AddressAdmin Dynamic Address QueryAdmin Save Configuration Admin Port MirroringClick the Reboot button, then click OK to confirm Admin Firmware UpgradeAdmin Reboot Admin Factory DefaultAdmin Memory Logs Admin LoggingAdmin Flash Logs If you select Yes, a confirmation screen appears LogoutGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Glossary Appendix B GlossaryGlossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix B Specifications Appendix C SpecificationsSLM2024/SLM2048 UL, cUL, CE mark, CB Power Internal Power CertificationConnectors for 10BASE-T Buttons Reset Cabling Type UTP CAT 5 or better for28 lb 3.3 kg Unit Weight39 lb 2.9 kg 83 lb 3.1 kgLimited Warranty Appendix D Warranty and Regulatory InformationRèglement d’Industry Canada Safety NoticesFCC Statement Industry Canada StatementDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Contact Information Appendix E
Top Page Image Contents