Linksys SLM2048, SLM248P, SLM248G Chapter Configuration Using Web-based Utility, Setup Summary

Page 16

Chapter 4

Chapter 4:

Configuration Using the

Web-based Utility

This chapter describes the features included in the Web- based Utility. All features shown in this chapter, unless specifically identified, are included in the all of Smart Switches. Unique features for specific Switches are noted.

NOTE: The web-based utility is optimized for

ascreen resolution of 1024 x 768. Internet Explorer version 5.5 or above is recommended..

To use the utility, open your web browser, enter http://192.168.1.254 in the Address field, then press Enter.

Address Bar

NOTE: The default IP address is 192.168.1.254. If you have changed the IP address or are using DHCP to assign it, enter the new IP address instead. The computer you use for configuration should be on the same subnet as the Switch.

The Login screen appears. Enter admin in the Username field and enter the password in the Password field. If this is the first time you are using the utility, leave the Password blank. Then press OK to log in. The Setup tab’s Summary screen appears.

(After you have completed your first login, for security purposes it is recommended that you set a password at a later time. For detailed information on changing the password, refer to section “Admin > User Authentication.”)

Login Screen

Business Series Smart Gigabit Ethernet Switch

Configuration Using the Web-based Utility

Each time you log in, the web-based utility first displays the Setup tab’s Summary screen. To access another screen, you first select the appropriate category from among the 10 tabs that appear at the top of the screen: Setup, Port Management, VLAN Management, Statistics, Security, QoS, Spanning Tree, Multicast, Admin, and Logout. Then, select the desired screen from the list directly below the tab names.

Setup

The Setup tab contains the Summary screen. This screen displays basic system information.

Setup > Summary

The Summary screen displays a summary of Switch information. The settings shown cannot be modified from the Summary screen; however, many of them can be modified from the Setup tab’s Network Settings screen.

Setup > Summary

At the top of the Summary screen, an image of the Switch‘s front panel provides the following color-coded status information for the Switch’s Ethernet ports:

Green  Indicates that the port has a connection. Gray  Indicates that the port has no connection.

Orange  Indicates that the port has been closed down by the administrator.

Click on a port to display that port’s statistics.

NOTE: The port colors in the Summary screen are not related to the colors of the LEDs on the Switch’s ports. The port LEDs display different status information, as described in “Chapter 2: Overview.”

The Summary screen two sections: Device Information and System Information. These are described below.

11

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Business Series Smart Gigabit Ethernet Switch About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Table of Contents Appendix D Warranty and Regulatory Information Appendix B Glossary Appendix C SpecificationsAppendix E Contact Information Chapter Introduction IntroductionChapter Product Overview Product OverviewSLM2048 Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Chapter Installation InstallationPre-Installation Considerations Placement OptionsDesktop Placement Hardware InstallationRack-Mount Placement Uplinking the Switch WithSetup Chapter Configuration Using Web-based UtilitySetup Summary Setup Network Settings Device InformationSystem Information IdentificationSetup Time IP ConfigurationLocal Time Daylight SavingPort Configuration Port Management Port SettingsPort Management Port Management Link Aggregation LAG Configuration Port Management PoE Power Settings Port Management LacpGlobal Parameter Port PriorityVlan Management Port Settings Vlan ManagementVlan Management Create Vlan Vlan Management Port to VlanVlan Management Vlan to Port Port The number of the port being configuredJoin Vlan to Port Statistics Statistics Interface StatisticsInterface Ethernet-likeSecurity 802.1x Settings Setting TimerSecurity ParametersSecurity Port Security Security IP Access List Security Storm ControlIP Address Enter the IP address to be allowed Broadcast Only Counts only Broadcast trafficSecurity Radius QoS CoS Settings CoS SettingsCoS Default QoSQoS Dscp Settings QoS Queue SettingsQoS Basic Mode Global Setting Spanning TreeSpanning Tree STP Status Spanning Tree Global STPBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Vlan Igmp Settings MulticastMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Admin Admin User AuthenticationUser Authentication Local User EditAdmin Static Address Admin Dynamic AddressQuery Secure The entry is defined for locked portsAdmin Port Mirroring Admin Save ConfigurationAdmin Firmware Upgrade Admin RebootAdmin Factory Default Click the Reboot button, then click OK to confirmAdmin Memory Logs Admin LoggingAdmin Flash Logs Logout If you select Yes, a confirmation screen appearsGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Appendix B Glossary GlossaryGlossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix B Specifications Appendix C SpecificationsSLM2024/SLM2048 Power Internal Power Certification Connectors for 10BASE-TButtons Reset Cabling Type UTP CAT 5 or better for UL, cUL, CE mark, CBUnit Weight 39 lb 2.9 kg83 lb 3.1 kg 28 lb 3.3 kgAppendix D Warranty and Regulatory Information Limited WarrantySafety Notices FCC StatementIndustry Canada Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Appendix E Contact Information
Top Page Image Contents