Linksys Official Manual for Switches: Overview and Features for SLM2024, SLM2048, SLM224G, SLM248P
Page 8

Chapter 2

Product Overview

SLM2024

Front Panel

The Switch’s LEDs and ports are located on the front panel.

Front Panel of the SLM2024

SYSTEM  (Green)  Lights up to indicate that the Switch is powered on. Blinks while the Switch is performing a system self-test.

LNK/ACT (1-24) (Green) Lights up to indicate a functional 10/100/1000 Mbps network link through the corresponding port (1 through 24) with an attached device. Blinks to indicate that the Switch is actively sending or receiving data over that port.

Gigabit (1-24) (Amber) Lights up to indicate a functional 1000 Mbps connection on the corresponding port (1 through 24) with an attached device.

Reset  Press and hold the Reset Button for less than ten seconds to reboot the Switch. Press and hold the Reset Button for more than ten seconds to reset the Switch’s settings to the factory defaults.

Ethernet 1-24 The Switch is equipped with 24 auto-sensing, Ethernet network ports, which use RJ-45 connectors. The Fast Ethernet ports support network speeds of 10 Mbps, 100 Mbps, or 1000 Mbps. They can operate in half- and full- duplex modes. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10 Mbps, 100 Mbps, or 1000 Mbps), and adjust its speed and duplex accordingly.

miniGBIC (1-2) The miniGBIC (gigabit interface converter) port is a connection point for a miniGBIC expansion module, so the Switch can be uplinked via fiber to another switch. The MiniGBIC port provides a link to a high-speed network segment or individual workstation at speeds of up to 1000 Mbps.

To establish a Gigabit Ethernet connection using a miniGBIC port, you will need to install a MGBT1, MGBSX1, or MGBLH1 Gigabit expansion module and use Category 5e cabling or fiber optic cabling.

To establish a Fast Ethernet connection using a miniGBIC port, you will need to install a MFEFX1 (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP Transceiver and use fiber optic cabling.

NOTE:  On the SLM2024, MiniGBIC ports are shared with standard ports. If a miniGBIC port is used, then the shared standard port on the Switch cannot be used. The following table defines the shared port mapping of the SLM2024 Switch.

SLM2024 Shared Port Mapping

miniGBIC Port

Standard Port

 

 

miniGBIC 1

Port 12

miniGBIC 2

Port 24

 

 

Back Panel

The power port is located on the back panel of the Switch.

Back Panel of the SLM2024

POWER  The Power port is where you connect the AC power.

Business Series Smart Gigabit Ethernet Switch



Page 7 Page 9
Image 8
Page 7 Page 9
Contents Business Series Smart Gigabit Ethernet Switch About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Table of Contents Appendix E Contact Information Appendix B Glossary Appendix C SpecificationsAppendix D Warranty and Regulatory Information Chapter Introduction IntroductionChapter Product Overview Product OverviewSLM2048 Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Chapter Installation InstallationPre-Installation Considerations Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement Uplinking the Switch WithSetup Summary Chapter Configuration Using Web-based UtilitySetup Setup Network Settings Device InformationSystem Information IdentificationSetup Time IP ConfigurationLocal Time Daylight SavingPort Management Port Management Port SettingsPort Configuration Port Management Link Aggregation LAG Configuration Port Management PoE Power Settings Port Management LacpGlobal Parameter Port PriorityVlan Management Port Settings Vlan ManagementVlan Management Create Vlan Vlan Management Port to VlanJoin Vlan to Port Port The number of the port being configuredVlan Management Vlan to Port Statistics Statistics Interface StatisticsInterface Ethernet-likeSecurity 802.1x Settings Setting TimerSecurity ParametersSecurity Port Security Security IP Access List Security Storm ControlIP Address Enter the IP address to be allowed Broadcast Only Counts only Broadcast trafficSecurity Radius QoS CoS Settings CoS SettingsCoS Default QoSQoS Basic Mode QoS Queue SettingsQoS Dscp Settings Global Setting Spanning TreeSpanning Tree STP Status Spanning Tree Global STPSpeed Displays the speed at which the port is operating Spanning Tree STP Port SettingsBridge Settings Vlan Igmp Settings MulticastMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Admin Admin User AuthenticationUser Authentication Local User EditAdmin Static Address Admin Dynamic AddressQuery Secure The entry is defined for locked portsAdmin Port Mirroring Admin Save ConfigurationAdmin Firmware Upgrade Admin RebootAdmin Factory Default Click the Reboot button, then click OK to confirmAdmin Flash Logs Admin LoggingAdmin Memory Logs Logout If you select Yes, a confirmation screen appearsFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Appendix B Glossary GlossaryGlossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix B SLM2024/SLM2048 Appendix C SpecificationsSpecifications Power Internal Power Certification Connectors for 10BASE-TButtons Reset Cabling Type UTP CAT 5 or better for UL, cUL, CE mark, CBUnit Weight 39 lb 2.9 kg83 lb 3.1 kg 28 lb 3.3 kgAppendix D Warranty and Regulatory Information Limited WarrantySafety Notices FCC StatementIndustry Canada Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Appendix E Contact Information
Top Page Image Contents