Linksys SLM224P, SLM248P, SLM248G, SLM2024, SLM2048, SLM224G manual Port Management Link Aggregation

Page 20

Chapter 4

Configuration Using the Web-based Utility

Reactivate Suspended Port  If the port has been suspended, select this checkbox to reactivate the port.

Operational Status  (Read-only) Displays whether the port is operational or non-operational.

Admin Speed  Use this to manually set the port’s configured transmission rate in Mbps. You can select 10M, 100M, or 1000M (Gigabit ports only). Before you change this setting, make sure that Auto Negotiation is disabled.

Current Port Speed  (Read-only) The port’s current rate in Mbps.

Admin Duplex  The port’s duplex mode, either Full or Half.

Current Duplex Mode  (Read-only) The port’s current duplex mode.

Auto Negotiation  Select Enable (default) or Disable to enable or disable Auto-Negotiation on the port. Auto- Negotiation allows a port to advertise its transmission rate, duplex mode, and flow control settings to other ports.

Current Auto Negotiation  (Read-only) The port’s current Auto-Negotiation status.

Admin Advertisement  Select the speed(s) and duplex mode(s) that the port will advertise. The available speeds are determined by the port type. The following capabilities are supported.

•Max Capability  The port advertises all speeds and duplex mode settings.

•10 Half  The port advertises 10 Mbps half-duplex operation.

•10 Full  The port advertises 10 Mbps full-duplex operation.

•100 Half  The port advertises 100 Mbps half-duplex operation.

•100 Full  The port advertises 100 Mbps full-duplex operation.

•1000 Full  (Gigabit ports only) The port advertises

1000 Mbps full-duplex operation.

Current Advertisement  (Read-only) The speed and duplex mode settings that the port is currently advertising.

Neighbor Advertisement  (Read-only) The speed and duplex mode settings that the neighbor port (the port to which the selected port is connected) is advertising. If the port has no neighbor port, this field displays “Unknown.”

Back Pressure  Select Enable or Disable (default) to enable or disable Back Pressure mode on the port.

Current Back Pressure  (Read-only) The current Back Pressure mode on the port.

Flow Control  Select Enable or Disable to manually enable or disable flow control, or select Auto-Negotiationfor automatic selection of flow control on the port.

Current Flow Control  (Read-only) The current flow control setting.

MDI/MDIX  Select the port’s MDI/MDIX type, either MDI, MDIX, or Auto (automatically detect type). The MDI setting is used if the port is connected to an end station. The MDIX setting is used if the port is connected to a hub or another switch.

Current MDI/MDIX  (Read-only) The port’s current MDI/ MDIX type.

LAG  (Read-only) The LAG to which this port belongs, if the port is a LAG member.

Click Save to save the settings and leave the screen open. Click Save & Close to save the settings and close the screen. Click Close to close the screen without saving the settings.

Port Management > Link Aggregation

You can create multiple links between devices that work as one virtual, aggregate link. This is known as a Link Aggregrated Group (LAG). LAGs offers a dramatic increase in bandwidth for network segments where bottlenecks exist, as well as providing a fault-tolerant link between two devices. You can create up to eight LAGs on the Switch. Each LAG can contain up to eight ports.

Port Management > Link Aggregation

LAG  The LAG number (1-8).

Description  The user-defined description for the LAG.

Admin Status  The administrative status of the interface. To change it, select Up to enable the interface, or Down to disable it.

Type  Indicates if a LAG has been manually configured (static) or dynamically set through LACP.

Link Status  Displays the status of the link.

Business Series Smart Gigabit Ethernet Switch

15

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Business Series Smart Gigabit Ethernet Switch About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Table of Contents Appendix E Contact Information Appendix B Glossary Appendix C SpecificationsAppendix D Warranty and Regulatory Information Chapter Introduction IntroductionChapter Product Overview Product OverviewSLM2048 Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Chapter Installation InstallationPre-Installation Considerations Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement Uplinking the Switch WithSetup Summary Chapter Configuration Using Web-based UtilitySetup Setup Network Settings Device InformationSystem Information IdentificationSetup Time IP ConfigurationLocal Time Daylight SavingPort Management Port Management Port SettingsPort Configuration Port Management Link Aggregation LAG Configuration Port Management PoE Power Settings Port Management LacpGlobal Parameter Port PriorityVlan Management Port Settings Vlan ManagementVlan Management Create Vlan Vlan Management Port to VlanJoin Vlan to Port Port The number of the port being configuredVlan Management Vlan to Port Statistics Statistics Interface StatisticsInterface Ethernet-likeSecurity 802.1x Settings Setting TimerSecurity ParametersSecurity Port Security Security IP Access List Security Storm ControlIP Address Enter the IP address to be allowed Broadcast Only Counts only Broadcast trafficSecurity Radius QoS CoS Settings CoS SettingsCoS Default QoSQoS Basic Mode QoS Queue SettingsQoS Dscp Settings Global Setting Spanning TreeSpanning Tree STP Status Spanning Tree Global STPSpeed Displays the speed at which the port is operating Spanning Tree STP Port SettingsBridge Settings Vlan Igmp Settings MulticastMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Admin Admin User AuthenticationUser Authentication Local User EditAdmin Static Address Admin Dynamic AddressQuery Secure The entry is defined for locked portsAdmin Port Mirroring Admin Save ConfigurationAdmin Firmware Upgrade Admin RebootAdmin Factory Default Click the Reboot button, then click OK to confirmAdmin Flash Logs Admin LoggingAdmin Memory Logs Logout If you select Yes, a confirmation screen appearsFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Appendix B Glossary GlossaryGlossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix B SLM2024/SLM2048 Appendix C SpecificationsSpecifications Power Internal Power Certification Connectors for 10BASE-TButtons Reset Cabling Type UTP CAT 5 or better for UL, cUL, CE mark, CBUnit Weight 39 lb 2.9 kg83 lb 3.1 kg 28 lb 3.3 kgAppendix D Warranty and Regulatory Information Limited WarrantySafety Notices FCC StatementIndustry Canada Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Appendix E Contact Information
Top Page Image Contents