Linksys SLM248G, SLM248P, SLM224P, SLM2024 manual Admin Static Address, Admin Dynamic Address, Query

Page 37

Chapter 4

Configuration Using the Web-based Utility

Admin > Static Address

Admin > Static Address

The Static Address screen lets you assign a static address to a specific interface on the Switch. A static address is bound to its assigned interface and cannot be moved. If a static address is seen on an interface to which it is not assigned, the address is ignored and is not written to the address table.

A list of all static addresses on the Switch is displayed at the bottom of the Static Address screen. The top section of the screen contains the following fields that you use to create static address entries.

Interface  The interface that is associated with the static address. Select Port or LAG, then select the desired interface from the accompanying drop-down menu.

MAC Address  This is the physical address that is being mapped to the specified interface.

VLAN ID  The VLAN ID number (1-4093) of the configured VLAN that is associated with the specified interface. If you use this field the VLAN Name field is disabled.

VLAN Name  The name of the VLAN associated with the specified interface. If you use this field, the VLAN ID field is disabled.

Status  The static address type. The possible values are::

•Permanent (default)  Keep the entry permanently.

•Delete on Reset  Delete the entry when the Switch is reset.

•Delete on Timeout  Delete the entry when a timeout occurs. The default timeout period is 300 seconds.

•Secure  The entry is defined for locked ports.

After you have entered the information listed above, click Add to List. The static address will then appear in the list of static addresses. To delete a static MAC address from the list, select the entry in the list, then click Remove.

Admin > Dynamic Address

Admin > Dynamic Address

The Dynamic Address Table contains MAC addresses learned by monitoring the source address on inbound traffic. When the destination address of inbound traffic is found in the table, packets intended for that address are forwarded directly to the associated port. Otherwise, the traffic is flooded to all ports.

The Dynamic Address screen lets you query the table to find specific dynamic MAC addresses, or display MAC addresses associated with a specific interface or VLAN. Query criteria include interface type, MAC address, VLAN, and table sort key. You can also set the Dynamic MAC Address Table’s address aging parameter or clear the table.

Address Aging  Specifies the amount of time (in seconds) that a MAC address remains in the Dynamic MAC Address table before it times out, if no traffic from the source is detected. The default value is 300 seconds.

Clear Table  If checked, this clears the MAC Address table.

Query

Interface  Use this to query the table for a specific port or LAG. Select Port or LAG and select the interface from the drop-down menu.

MAC Address  Use this to query the table for a specific MAC address. Enter the MAC address in the field.

VLAN ID  Use this to query the table for a specific VLAN ID. Enter the VLAN ID in the field.

Address Table Sort Key  Specifies how the search results will be sorted—by Address, VLAN, or Interface.

Specify the search criteria (Interface, MAC Address, or VLAN) and the sort method for the search results, then click Query to display the dynamic addresses matching the search criteria.

Business Series Smart Gigabit Ethernet Switch

32

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Business Series Smart Gigabit Ethernet Switch About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Table of Contents Appendix D Warranty and Regulatory Information Appendix B Glossary Appendix C SpecificationsAppendix E Contact Information Introduction Chapter IntroductionProduct Overview Chapter Product OverviewSLM2048 Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Installation Chapter InstallationPre-Installation Considerations Placement OptionsDesktop Placement Hardware InstallationRack-Mount Placement With Uplinking the SwitchSetup Chapter Configuration Using Web-based UtilitySetup Summary Device Information Setup Network SettingsSystem Information IdentificationIP Configuration Setup TimeLocal Time Daylight SavingPort Configuration Port Management Port SettingsPort Management Port Management Link Aggregation LAG Configuration Port Management Lacp Port Management PoE Power SettingsGlobal Parameter Port PriorityVlan Management Vlan Management Port SettingsVlan Management Create Vlan Vlan Management Port to VlanVlan Management Vlan to Port Port The number of the port being configuredJoin Vlan to Port Statistics Interface Statistics StatisticsInterface Ethernet-likeSetting Timer Security 802.1x SettingsSecurity ParametersSecurity Port Security Security Storm Control Security IP Access ListIP Address Enter the IP address to be allowed Broadcast Only Counts only Broadcast trafficSecurity Radius CoS Settings QoS CoS SettingsCoS Default QoSQoS Dscp Settings QoS Queue SettingsQoS Basic Mode Spanning Tree Global SettingSpanning Tree STP Status Spanning Tree Global STPBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Multicast Vlan Igmp SettingsMulticast Igmp Snooping Multicast Bridge MulticastMulticast Bridge Multicast Forward All Admin User Authentication AdminUser Authentication Local User EditAdmin Dynamic Address Admin Static AddressQuery Secure The entry is defined for locked portsAdmin Save Configuration Admin Port MirroringAdmin Reboot Admin Firmware UpgradeAdmin Factory Default Click the Reboot button, then click OK to confirmAdmin Memory Logs Admin LoggingAdmin Flash Logs If you select Yes, a confirmation screen appears LogoutGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Glossary Appendix B GlossaryGlossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix B Specifications Appendix C SpecificationsSLM2024/SLM2048 Connectors for 10BASE-T Power Internal Power CertificationButtons Reset Cabling Type UTP CAT 5 or better for UL, cUL, CE mark, CB39 lb 2.9 kg Unit Weight83 lb 3.1 kg 28 lb 3.3 kgLimited Warranty Appendix D Warranty and Regulatory InformationFCC Statement Safety NoticesIndustry Canada Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Contact Information Appendix E
Top Page Image Contents