Linksys SLM2048 manual Port Management Lacp, Port Management PoE Power Settings, Global Parameter

Page 22

Chapter 4

Configuration Using the Web-based Utility

Port Management > LACP

In addition to LAGs that you create by manually grouping ports together, you can also use the Link Aggregation Control Protocol (LACP) to automatically negotiate a LAG link between the Switch and another network device.

The LACP screen contains fields for configuring LACP LAGs. This screen is divided into three parts: Global Parameter, Port Priority, and LACP Port Table.

Port Management > LACP

Global Parameter

LACP System Priority The global LACP priority value, from 1 to 65535. The default value is 1.

Port Priority

Port The port number to which the timeout and priority values are assigned. To configure a different port, select it from the drop-down menu. If you do not see the port you want, click Next in the LACP Port Table.

LACP Port Priority Defines the LACP priority value for the port, from 1 to 65535. The default value is 1.

LACP Timeout The administrative LACP timeout value. Select either Short or Long (default).

Admin Key (Read-only) A channel will only be formed between ports with the same admin key. This only applies to ports located on the same switch.

When you are finished entering the settings above, click Update to apply the settings.

LACP Port Table

This section provides a read-only display of the current LACP settings.

After you are finished setting the LACP parameters, click Save Settings to save the settings, or click Cancel Changes to cancel your changes.

Port Management > PoE Power Settings

NOTE: This section applies ONLY to the SLM224P and SLM248P Smart Switches.

The PoE Power Settings screen allows you to configure the Power over Ethernet (PoE) ports on the Switch.

Port Management > PoE Power Settings

Port Displays the port number.

Admin Status Check the checkbox to enable PoE power to be supplied to the connected device.

Priority Select Critical, High, or Low (default) from the drop‑down menu to set the priority of the port.

Power Allocation (milliwatts) Sets the maximum power in milliwatts that can be supplied to the port.

Power Consumption (milliwatts) Displays the power currently being used by the connected PoE device.

Click Save Settings to save the changes, or click Cancel Changes to cancel your changes.

Business Series Smart Gigabit Ethernet Switch

17

Image 22

Contents Business Series Smart Gigabit Ethernet Switch Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Table of Contents Appendix D Warranty and Regulatory Information Appendix B Glossary Appendix C SpecificationsAppendix E Contact Information Chapter Introduction IntroductionSLM2048 Chapter Product OverviewProduct Overview Back PanelSLM2024 SLM248G SLM248P SLM224G SLM224P Pre-Installation Considerations Chapter InstallationInstallation Placement OptionsDesktop Placement Hardware InstallationRack-Mount Placement Uplinking the Switch WithSetup Chapter Configuration Using Web-based UtilitySetup Summary System Information Setup Network SettingsDevice Information IdentificationLocal Time Setup TimeIP Configuration Daylight SavingPort Configuration Port Management Port SettingsPort Management Port Management Link Aggregation LAG Configuration Global Parameter Port Management PoE Power SettingsPort Management Lacp Port PriorityVlan Management Create Vlan Vlan Management Port SettingsVlan Management Vlan Management Port to VlanVlan Management Vlan to Port Port The number of the port being configuredJoin Vlan to Port Interface StatisticsStatistics Interface Statistics Ethernet-likeSecurity Security 802.1x SettingsSetting Timer ParametersSecurity Port Security IP Address Enter the IP address to be allowed Security IP Access ListSecurity Storm Control Broadcast Only Counts only Broadcast trafficSecurity Radius CoS Default QoS CoS SettingsCoS Settings QoSQoS Dscp Settings QoS Queue SettingsQoS Basic Mode Spanning Tree STP Status Global SettingSpanning Tree Spanning Tree Global STPBridge Settings Spanning Tree STP Port SettingsSpeed Displays the speed at which the port is operating Multicast Igmp Snooping Vlan Igmp SettingsMulticast Multicast Bridge MulticastMulticast Bridge Multicast Forward All User Authentication AdminAdmin User Authentication Local User EditQuery Admin Static AddressAdmin Dynamic Address Secure The entry is defined for locked portsAdmin Port Mirroring Admin Save ConfigurationAdmin Factory Default Admin Firmware UpgradeAdmin Reboot Click the Reboot button, then click OK to confirmAdmin Memory Logs Admin LoggingAdmin Flash Logs Logout If you select Yes, a confirmation screen appearsGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Appendix B Glossary GlossaryGlossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix B Specifications Appendix C SpecificationsSLM2024/SLM2048 Buttons Reset Cabling Type UTP CAT 5 or better for Power Internal Power CertificationConnectors for 10BASE-T UL, cUL, CE mark, CB83 lb 3.1 kg Unit Weight39 lb 2.9 kg 28 lb 3.3 kgAppendix D Warranty and Regulatory Information Limited WarrantyIndustry Canada Statement Safety NoticesFCC Statement Règlement d’Industry CanadaDansk Danish Miljøinformation for kunder i EU Appendix D Norsk Norwegian Miljøinformasjon for kunder i EU Appendix D Appendix E Contact Information