Linksys SRW208 manual Console Interface for Configuration for directions

Page 26

WebView Switches

Connecting the Switch

To connect network devices to the Switch, follow these instructions:

1.Make sure all the devices you will connect to the Switch are powered off.

2.For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the numbered ports on the Switch.

3.Connect the other end to a PC or other network device.

4.Repeat steps 2 and 3 to connect additional devices.

5.If you are using the mini-GBIC port, then connect the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the module’s documentation.

6.If you will use the Switch’s console interface to configure the Switch, then connect the supplied serial cable to the Switch’s Console port, and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (This PC must be running the VT100 terminal emulation software, such as HyperTerminal.)

7.Connect the supplied power cord to the Switch’s power port, and plug the other end into an electrical outlet.

IMPORTANT: Make sure you use the power cord that is supplied with the Switch. Use of a different power cord could damage the Switch.

8.Power on the network devices connected to the Switch. Each active port’s corresponding Link/Act LED will light up on the Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

If you will use the Switch’s console interface to configure the Switch, proceed to Chapter 4: Using the

Console Interface for Configuration for directions.

If you will use the Switch’s Web-based Utility to configure the Switch, proceed to Chapter 5: Using the

Web-based Utility for Configuration.

NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it.

Chapter 3: Connecting the Switch

15

Connecting the Switch

Image 26

Contents Port 10/100 Ethernet Switch Copyright and Trademarks Word definitionTable of Contents WebView Switches Appendix F Warranty Information 124 Appendix B Windows Help Appendix C Downloading using XmodemAppendix D Glossary Appendix E Specifications 104 WebView Switches Front Panel of the SRW208 Front Panel of the SRW208G18 SSH Keys Fingerprints 14 Vlan Management Vlan to Ports 44 Advanced Mode New Class Map 74 Admin Memory Logs Introduction WelcomeWebView Switches What’s in this User Guide? SRW208 Front Panel Getting to Know the SwitchOverview LEDsSRW208G Front Panel Ports1000Mbps, and adjust its speed and duplex accordingly SRW208L Front Panel Front Panel of the SRW208LSRW208P, SRW208MP Front Panel Speeds of up to 1000MbpsRJ-45 port G1 through G2 Power port is located on the back panel of the Switch Back PanelConnecting the Switch Maximum Cabling Distances From Maximum DistanceDesktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Attach the Brackets to the SwitchWall-Mount Placement Wall-Mount TemplateConsole Interface for Configuration for directions Using the Console Interface for Configuration Configuring the HyperTerminal ApplicationConnecting to the Switch through a Telnet Session COM1 PropertiesConfiguring the Switch through the Console Interface Switch Main MenuSystem Configuration Menu System Information Management Settings 14 SSH Configuration 17 SSH Crypto Key Generation Security Settings IP Configuration Http 27 Network Configuration File Management Port Status Using the Web-based Utility for Configuration Accessing the Web-based UtilitySystem Information Setup Tab SummaryDevice Information PoE Information Setup Tab Network SettingsIP Configuration IdentificationLocal Time Setup Tab TimeSet Time Daylight SavingPort Management Tab Port Settings Sntp ServersPort Configuration Detail screen Port Settings Port Configuration DetailWebView Switches Port Management Tab Link Aggregation Link Aggregation Detail screenPort Management Tab Lacp Port Management LacpSingle Vlan Port Management Tab PoE Power SettingsVlan Management Tab Create Vlan Vlan RangeVlan Management Tab Port Settings 12 Vlan Management Port SettingsVlan Management Tab Ports to Vlan 13 Vlan Management Ports to VlanVlan Management Tab Vlan to Ports Join Vlan Detail screenVlan Management Tab Gvrp Statistics Tab Rmon Statistics17 Statistics Rmon Statistics Statistics Tab Rmon History Log TableRmon History 19 Rmon History TableStatistics Tab Rmon Alarm 20 Statistics Rmon AlarmStatistics Tab Rmon Events Add EventStatistics Tab Port Utilization 22 Rmon Events Events LogStatistics Tab 802.1x Statistics Statistics Tab Gvrp StatisticsACL Tab IP Based ACL 26 ACL IP Based ACL WebView Switches ACL Tab MAC Based ACL 27 ACL Mac Based ACLSecurity Tab ACL Binding Security Tab RadiusSecurity Tab TACACS+ 30 Security TACACS+Security Tab 802.1x Settings Setting Timer screenSecurity Tab Port Security 33 Security Port SecuritySecurity Tab Multiple Hosts Security Tab Storm Control 34 Security Multiple HostsQoS Tab CoS Settings QoSQoS Tab Queue Settings CoS DefaultQoS Tab Dscp Settings QoS Tab BandwidthOut of Profile Dscp screen QoS Tab Basic ModeQoS Tab Advanced Mode Policy Name screen42 Advanced Mode Out of Profile Dscp New Class Map screenSpanning Tree New Aggregate Policer screenSpanning Tree Tab STP Status 46 Spanning Tree STP StatusSpanning Tree Tab Global STP Global SettingBridge Settings Spanning Tree Tab STP Port Settings 48 Spanning Tree STP Port SettingsSpanning Tree Tab Rstp Port Settings 49 Spanning Tree Rstp Port SettingsWebView Switches Spanning Tree Tab Mstp Instance Settings Spanning Tree Tab Mstp PropertiesSpanning Tree Tab Mstp Interface Settings Link is working in Rstp or STP modeMulticast Tab Igmp Snooping 53 Multicast Igmp Snooping Multicast Tab Bridge Multicast 54 Multicast Bridge MulticastMulticast Tab Bridge Multicast Forward All Snmp Tab Global ParametersSnmp Tab Views Snmp Tab Group Profile58 Snmp Group Profile Snmp Tab Group Membership 59 Snmp Group MembershipSnmp Tab Communities Base TableSnmp Tab Notification Filter Advanced TableSnmp Tab Notification Recipient 62 Snmp Notification RecipientAdmin Tab User Authentication 63 Admin User AuthenticationAdmin Tab Static Address QueryAdmin Tab Dynamic Address Admin Tab Logging 66 Admin LoggingAdmin Tab Port Mirroring Admin Tab Cable TestAdmin Tab Save Configuration 69 Admin Save ConfigurationAdmin Tab Firmware Upgrade Admin Tab RebootAdmin Tab Factory Defaults Admin Tab Server LogsAdmin Tab Memory Logs Admin Tab Flash LogsGigabit Ethernet Fiber Optic CablingNetwork Neighborhood/My Network Places Appendix B Windows HelpShared Resources Appendix C Downloading using Xmodem Startup Menu ProceduresFigure C-2 Send File Appendix D Glossary WebView Switches WebView Switches 100 101 102 103 Appendix E Specifications SRW208Xmodem upgrade Tftp upgradeBootP Cable DiagnosticsPort EthertypeClassification and Remarking ACLs TCP/UDP port basedDiffserv Rate Limiting Ingress policer Egress rate control StandardsSRW208G 1 miniGBIC/SFP portRFC 2618 Radius Client MIB RFC 1215 Traps 110 802.1x Port Access Authentication SRW208L 113 114 115 SRW208MP With 2 SFP slotsSnmp version 1, 2c, 3 with support for traps RFC 2618 Radius Client MIB, RFC 1215 Traps, Private POE MIB118 119 SRW208P 121 122 123 Appendix F Warranty Information Limited WarrantyAppendix G Regulatory Information FCC Statement126 127 128 129 130 Appendix H Contact Information

Related manuals

Manual 86 pages 25.84 Kb