Adaptec 1225SA, 58300, 44300, 48300, 1220SA, 1420SA, 1430SA manual Setting the Boot Controller

Page 33

Chapter 4: Installing the HostRAID Controller and Disk Drives l 33

4Select SATASelect (on SATA controller) and SerialSelect (on SAS controller) to verify the hardware configuration of the controller and the drives.

Verify that all drives are shown. If anything appears to be missing, power down the computer and check the connections.

Setting the Boot Controller

Note: If your system contains only one bootable controller, or if you are using the 1225SA controller that does not support bootable devices, proceed with Creating an Array on page 39.

Most of the Adaptec HostRAID controllers support bootable disk drives and arrays. The default setting of the HostRAID controller and system Setup allows you to install and boot from either a disk drive connected to the motherboard, or from a drive or array connected to the HostRAID controller. To enable the system to boot from either a disk drive or an array connected to the HostRAID controller:

Note: Selecting the boot controller is done using the system BIOS Setup Utility. Launching the system BIOS Setup Utility varies depending on your computer model. Refer to your computer documentation for instructions on how to access the system BIOS.

1Enter the system BIOS Setup.

2Navigate to the disk drive boot sequence.

3Move the boot controller to the top of the list.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents SAS and Sata HostRAID Controller Copyright Adaptec Customer Support Limited 3-Year Hardware Warranty Regulatory Compliance Statements Contents Getting Started Managing Your Storage Space Using the ARC Utility Safety Information What You Need to Know Before You Begin About This GuideWhat You Need to Know Before You Begin How to Find More InformationTerminology Used in this Guide Conventions Used in This GuideAbout This Guide l About Your HostRAID Controller Array Level Features HostRAID Controller FeaturesAbout Your HostRAID Controller l PCI-X About the Adaptec 58300 ControllerAbout the Adaptec 48300 Controller About the Adaptec 44300 Controller About the Adaptec 1430SA Controller About the Adaptec 1420SA Controller About the Adaptec 1220SA Controller About the Adaptec 1225SA Controller Kit Contents and System Requirements System Requirements Kit ContentsInstalling the HostRAID Controller Disk Drives Before You Begin Installing the HostRAID ControllerSelecting SAS Cables Selecting Disk DrivesInstalling the HostRAID Controller and Disk Drives l Selecting Sata Cables Connecting Disk Drives to SAS HostRAID ControllersConnecting to a Backplane Connecting Directly to the HostRAID ControllerConnecting Disk Drives to Sata HostRAID Controllers Installing the SAS HostRAID Controller to a SAS ExpanderChecking Your Controller and Devices Setting the Boot Controller Next Steps Getting Started Basic Installation Steps Choosing Installation OptionsInstalling with an Operating System Choosing a RAID LevelInstalling on an Existing Operating System Creating a Bootable Array Creating an Array Creating an Array with the ACUCreating an Array with Adaptec Storage Manager Select Express configuration..., then click Next Making Your Array BootableInstalling the Driver and an Operating System Creating a Driver Disk Installing with WindowsInstalling with Suse Linux Installing with Red Hat LinuxInstalling with NetWare Installing the Driver on an Existing Operating System Creating a Driver Disk or an Array Installing on Windows XP or WindowsInstalling on Windows Vista Installing on Red Hat or Suse LinuxInstalling on NetWare Continue with Managing Your Storage Space on Managing Your Storage Space About the Hrconf Command Line Utility Installing Adaptec Storage ManagerAbout Adaptec Storage Manager About the ARC Utility About the Adaptec Flash UtilityWhich Utility Should I Use? Solving Problems Recovering from a Disk Drive Failure Troubleshooting ChecklistFailed Disk Drive Protected by a Hot Spare Failed Disk Drive Not Protected by a Hot SpareFailure in Multiple Arrays Simultaneously Resetting the ControllerDisk Drive Failure in a RAID 0 Array Multiple Failures in the Same ArraySolving Problems l Understanding RAID RAID 0 Non-RAID Arrays RAID Technology OverviewUnderstanding Drive Segments Stripe-Unit SizeRAID 10 Arrays RAID 1 ArraysSelecting the Best RAID Level Introduction to SAS Terminology Used in This Appendix What is SAS?How Do SAS Devices Communicate? What’s a Phy?What’s a SAS Port? What’s a SAS Address? What’s a SAS Connector?What do SAS Cables Look Like? How are Disk Drives Identified in SAS?Direct-Attach Connections What are the SAS Connection Options?Backplane Connections SAS Expander ConnectionsSAS Domain How is SAS Different from Parallel SCSI?Parallel Scsi Serial Attached Scsi Using the ARC Utility Running the ARC Utility Introduction to the ARC UtilityCreating and Managing Arrays Creating a New ArrayQuick Init Creating a RAID 0 on new drives Managing Arrays Rebuilding ArraysViewing Array Properties Adding/Deleting Hot Spares Deleting ArraysEnabling/Disabling Write Cache Managing Bootable Arrays and Devices Using SerialSelectConfiguring Disk Drives Atapi SupportDevice SerialSelect OptionsPHY Configuration Using SATASelectSATASelect Options Formatting and Verifying Disk DrivesIdentifying Disk Drives Locating Disk DrivesViewing the Event Log DOS Using the Adaptec Flash Utility forIntroduction Compatibility InformationObtaining the Firmware Running the AFU Creating the Firmware Kit On Floppy DisksRunning the Menu-Based AFU AFU Commands Running the AFU from the Command LineExamples Command Syntax Command SwitchesExample Update \ AFU Verify /C Updating Flash Using AFU Command LineTo update a single HostRAID controller HostRAID Controller LED and I2C Connector Reference Adaptec 48300 Activity LED Connector Specification Adaptec 58300 Activity LED Connector SpecificationAdaptec 1430SA Activity LED and I2C Connector Specification Adaptec 44300 Activity LED Connector SpecificationLedsum Adaptec 1420SA Activity LED and I2C Connector SpecificationAdaptec 1225SA Activity LED Specification Adaptec 1220SA Activity LED Connector SpecificationElectrostatic DischargeESD Safety InformationTechnical Specifications Environmental Specifications DC Power RequirementsCurrent Requirements Glossary Configured array ConfigureConsistency check command BuildDisk ID Fault-tolerant arrayDrive LED EventLegacy disk Native Command QueuingLogical device Low-level formatSimple volume RAID volumeRAID signature RebuildStripe size VolumeStriped array TaskACU IndexSATASelect SerialSelect utilities SATASelect Adaptec, Inc

1430SA, 1225SA, 1420SA, 1220SA, 48300 specifications

Adaptec, a prominent name in the world of storage solutions, offers a diverse array of RAID controller cards aimed at enhancing data storage and management in both consumer and enterprise markets. Among its acclaimed products are the Adaptec 1220SA, 1430SA, 44300, 1225SA, and 1420SA. These cards ensure increased data protection, improved performance, and greater scalability.

The Adaptec 1220SA is a robust SATA RAID controller designed for small to medium-sized businesses. It supports RAID levels 0, 1, 1E, 5, and 10, providing flexibility for users to optimize data redundancy and performance. With the capability of handling up to four SATA drives, it guarantees an efficient and reliable setup while minimizing potential data loss. The controller also features an intuitive web-based management interface, making it easier to administer and configure.

The Adaptec 1430SA extends similar functionality with enhanced features. It is designed to accommodate up to eight SATA drives and supports the latest 3 Gbps SATA technology. This model includes optional battery backup for preserving critical data during unexpected power outages, ensuring that users maintain data integrity and protection at all times.

In the enterprise domain, the Adaptec 44300 shines as a high-performance RAID controller. It offers support for 12 SATA drives, which allows for expansive storage scalability, crucial for data-intensive applications. The advanced RAID features include support for RAID 6, providing dual parity data protection. The controller is built with a powerful processor and memory, allowing for faster data processing and enhanced throughput.

The Adaptec 1225SA is another noteworthy model. Designed for entry-level RAID applications, it offers a balanced combination of performance and reliability. Supporting up to four SATA drives, the 1225SA is particularly well-suited for environments where uptime is critical, delivering functionalities such as hot-swapping. This feature allows users to replace failed drives without shutting down the system, significantly reducing downtime.

Lastly, the Adaptec 1420SA caters to users who require a cost-effective but reliable storage solution. With support for RAID 0, 1, and JBOD, it is a versatile option for enthusiasts and small businesses. The controller can manage up to two SATA drives, making it ideal for basic applications where simplicity and efficiency are paramount.

Collectively, these Adaptec controllers showcase cutting-edge RAID technology and storage management features, reinforcing their position as reliable options for users ranging from home users to enterprise-level organizations seeking optimal data storage solutions.
Top Page Image Contents