Adaptec 1420SA, 58300, 44300, 48300, 1220SA, 1225SA, 1430SA manual Using SATASelect, PHY Configuration

Page 74

 

 

 

Appendix C: Using the ARC Utility 75

 

 

 

 

 

SerialSelect Options

Available Settings

Description

 

Physical Drives Display

Enabled

When Enabled, connected physical devices are

 

during Post

Disabled

displayed during system POST. Displaying the

 

 

 

devices adds a few seconds to the overall POST

 

 

 

time.

 

PHY Configuration

 

 

 

PHY Rate

Auto, 1.5, 3.0

The data transfer rate between the HostRAID

 

 

 

controller and devices. The default setting is

 

 

 

Automatic, which allows the SAS HostRAID

 

 

 

controller to adjust the speed as needed.

 

SAS Address

0-F

Specifies the last digit of a 64-bit SAS address of

 

 

 

the HostRAID controller, device, and each port

 

 

 

using a globally unique worldwide name (WWN)

 

 

 

identifier.

 

Controller Properties

 

 

 

PCI Slot: Bus:

None

Displays the path of the storage devices in a Host

 

Device:Function

 

RAID controller.

 

Interrupt (IRQ) Channel

None

Displays interrupt

 

I/O Port Address

None

Displays I/O port address

 

Device ID

None

Displays device ID

 

Controller Serial

None

Displays controller serial number

 

Number

 

 

 

Controller WWN

None

Displays the controller WWN

 

 

 

 

Using SATASelect

The SATASelect utility allows you to change the BIOS and SATA HostRAID controller and device settings without opening the computer cabinet.

To access SATASelect:

1Restart the computer, then press Ctrl+A when prompted to access the ARC utility.

2If multiple HostRAID controllers are installed, select the HostRAID controller you want to configure, then press Enter.

3From the ARC menu, select SATASelect Utility.

4To select a menu option, browse with the arrow keys to the option, then press Enter. In some cases, selecting an option displays another menu. You can return to the previous menu at any time by pressing Esc.

5To restore the default SATASelect values, press F6 from within the SATA Driver and Controller Configuration screen.

6To exit SATASelect, press Esc until a message prompts you to exit (if you changed any settings, you are prompted to save the changes before you exit).

7At the prompt, select Yes to exit, then press any key to restart the computer. Any changes you made in SATASelect take effect after the computer restarts.

Image 74
Contents SAS and Sata HostRAID Controller Copyright Adaptec Customer Support Limited 3-Year Hardware Warranty Regulatory Compliance Statements Contents Getting Started Managing Your Storage Space Using the ARC Utility Safety Information About This Guide What You Need to Know Before You BeginTerminology Used in this Guide How to Find More InformationWhat You Need to Know Before You Begin Conventions Used in This GuideAbout This Guide l About Your HostRAID Controller HostRAID Controller Features Array Level FeaturesAbout Your HostRAID Controller l About the Adaptec 58300 Controller PCI-XAbout the Adaptec 48300 Controller About the Adaptec 44300 Controller About the Adaptec 1430SA Controller About the Adaptec 1420SA Controller About the Adaptec 1220SA Controller About the Adaptec 1225SA Controller Kit Contents and System Requirements Kit Contents System RequirementsInstalling the HostRAID Controller Disk Drives Installing the HostRAID Controller Before You BeginSelecting Disk Drives Selecting SAS CablesInstalling the HostRAID Controller and Disk Drives l Connecting Disk Drives to SAS HostRAID Controllers Selecting Sata CablesConnecting Directly to the HostRAID Controller Connecting to a BackplaneChecking Your Controller and Devices Connecting Disk Drives to Sata HostRAID ControllersInstalling the SAS HostRAID Controller to a SAS Expander Setting the Boot Controller Next Steps Getting Started Installing with an Operating System Choosing Installation OptionsBasic Installation Steps Choosing a RAID LevelInstalling on an Existing Operating System Creating a Bootable Array Creating an Array with Adaptec Storage Manager Creating an ArrayCreating an Array with the ACU Making Your Array Bootable Select Express configuration..., then click NextInstalling the Driver and an Operating System Installing with Windows Creating a Driver DiskInstalling with Red Hat Linux Installing with Suse LinuxInstalling with NetWare Installing the Driver on an Existing Operating System Installing on Windows XP or Windows Creating a Driver Disk or an ArrayInstalling on NetWare Installing on Windows VistaInstalling on Red Hat or Suse Linux Continue with Managing Your Storage Space on Managing Your Storage Space About Adaptec Storage Manager About the Hrconf Command Line UtilityInstalling Adaptec Storage Manager Which Utility Should I Use? About the ARC UtilityAbout the Adaptec Flash Utility Solving Problems Failed Disk Drive Protected by a Hot Spare Troubleshooting ChecklistRecovering from a Disk Drive Failure Failed Disk Drive Not Protected by a Hot SpareDisk Drive Failure in a RAID 0 Array Resetting the ControllerFailure in Multiple Arrays Simultaneously Multiple Failures in the Same ArraySolving Problems l Understanding RAID Understanding Drive Segments RAID Technology OverviewRAID 0 Non-RAID Arrays Stripe-Unit SizeRAID 1 Arrays RAID 10 ArraysSelecting the Best RAID Level Introduction to SAS What is SAS? Terminology Used in This AppendixWhat’s a SAS Port? How Do SAS Devices Communicate?What’s a Phy? What do SAS Cables Look Like? What’s a SAS Connector?What’s a SAS Address? How are Disk Drives Identified in SAS?Backplane Connections What are the SAS Connection Options?Direct-Attach Connections SAS Expander ConnectionsHow is SAS Different from Parallel SCSI? SAS DomainParallel Scsi Serial Attached Scsi Using the ARC Utility Creating and Managing Arrays Introduction to the ARC UtilityRunning the ARC Utility Creating a New ArrayQuick Init Creating a RAID 0 on new drives Viewing Array Properties Managing ArraysRebuilding Arrays Enabling/Disabling Write Cache Adding/Deleting Hot SparesDeleting Arrays Configuring Disk Drives Using SerialSelectManaging Bootable Arrays and Devices Atapi SupportSerialSelect Options DeviceUsing SATASelect PHY ConfigurationFormatting and Verifying Disk Drives SATASelect OptionsLocating Disk Drives Identifying Disk DrivesViewing the Event Log Using the Adaptec Flash Utility for DOSObtaining the Firmware IntroductionCompatibility Information Running the Menu-Based AFU Running the AFUCreating the Firmware Kit On Floppy Disks Examples AFU CommandsRunning the AFU from the Command Line Example Command SyntaxCommand Switches Update Updating Flash Using AFU Command Line \ AFU Verify /CTo update a single HostRAID controller HostRAID Controller LED and I2C Connector Reference Adaptec 58300 Activity LED Connector Specification Adaptec 48300 Activity LED Connector SpecificationAdaptec 44300 Activity LED Connector Specification Adaptec 1430SA Activity LED and I2C Connector SpecificationAdaptec 1420SA Activity LED and I2C Connector Specification LedsumAdaptec 1220SA Activity LED Connector Specification Adaptec 1225SA Activity LED SpecificationSafety Information Electrostatic DischargeESDTechnical Specifications Current Requirements Environmental SpecificationsDC Power Requirements Glossary Consistency check command ConfigureConfigured array BuildDrive LED Fault-tolerant arrayDisk ID EventLogical device Native Command QueuingLegacy disk Low-level formatRAID signature RAID volumeSimple volume RebuildStriped array VolumeStripe size TaskIndex ACUSATASelect SerialSelect utilities SATASelect Adaptec, Inc

1430SA, 1225SA, 1420SA, 1220SA, 48300 specifications

Adaptec, a prominent name in the world of storage solutions, offers a diverse array of RAID controller cards aimed at enhancing data storage and management in both consumer and enterprise markets. Among its acclaimed products are the Adaptec 1220SA, 1430SA, 44300, 1225SA, and 1420SA. These cards ensure increased data protection, improved performance, and greater scalability.

The Adaptec 1220SA is a robust SATA RAID controller designed for small to medium-sized businesses. It supports RAID levels 0, 1, 1E, 5, and 10, providing flexibility for users to optimize data redundancy and performance. With the capability of handling up to four SATA drives, it guarantees an efficient and reliable setup while minimizing potential data loss. The controller also features an intuitive web-based management interface, making it easier to administer and configure.

The Adaptec 1430SA extends similar functionality with enhanced features. It is designed to accommodate up to eight SATA drives and supports the latest 3 Gbps SATA technology. This model includes optional battery backup for preserving critical data during unexpected power outages, ensuring that users maintain data integrity and protection at all times.

In the enterprise domain, the Adaptec 44300 shines as a high-performance RAID controller. It offers support for 12 SATA drives, which allows for expansive storage scalability, crucial for data-intensive applications. The advanced RAID features include support for RAID 6, providing dual parity data protection. The controller is built with a powerful processor and memory, allowing for faster data processing and enhanced throughput.

The Adaptec 1225SA is another noteworthy model. Designed for entry-level RAID applications, it offers a balanced combination of performance and reliability. Supporting up to four SATA drives, the 1225SA is particularly well-suited for environments where uptime is critical, delivering functionalities such as hot-swapping. This feature allows users to replace failed drives without shutting down the system, significantly reducing downtime.

Lastly, the Adaptec 1420SA caters to users who require a cost-effective but reliable storage solution. With support for RAID 0, 1, and JBOD, it is a versatile option for enthusiasts and small businesses. The controller can manage up to two SATA drives, making it ideal for basic applications where simplicity and efficiency are paramount.

Collectively, these Adaptec controllers showcase cutting-edge RAID technology and storage management features, reinforcing their position as reliable options for users ranging from home users to enterprise-level organizations seeking optimal data storage solutions.