Adaptec 48300 Using SerialSelect, Managing Bootable Arrays and Devices, Configuring Disk Drives

Page 72

Appendix C: Using the ARC Utility 73

Managing Bootable Arrays and Devices

Select the Manager Boot Unit option to add or remove a bootable array or single drive.

1From the ACU menu, select Manage Boot Unit.

2Use the up and down arrow keys to highlight the array or single drive you want to designate as a bootable device, then select Insert>Enter.

Note: Adaptec 1225SA controller does not support bootable devices.

Configuring Disk Drives

!Caution:

If the drive is used in an array, you may not be able to use the array again. Do not configure a drive that is part of a boot array. To determine which drives are associated with a particular array, see Viewing Array Properties on page 71.

The partition table on the disk will be deleted when deleting a simple volume.

To configure drives:

Note: Configuring disk drives makes a simple volume. A simple volume can be managed like normal arrays by using the Manage Arrays option on your Main menu.

1From the menu, select Configure Drives.

2Use the up and down arrow keys to highlight the disk you wish to configure, then press Insert.

3Repeat the previous step, if you want to add another drive to be configured.

4Press Enter.

5Read the warning message and ensure that you have selected the correct disk drives to configure. Type Y to continue.

ATAPI Support

The following devices are supported:

The 1225SA and 1220SA supports detection of SATA ATAPI TAPE Drive and CDROM.

The 1225SA and 1220SA supports booting from the ELTORITO bootable CD/DVD media.

If a bootable CD/DVD media is detected, that bootable media gets precedence in the booting order.

Using SerialSelect

The SerialSelect utility allows you to change the BIOS and SAS HostRAID controller and device settings without opening the computer cabinet.

For more information, see SerialSelect Options on page 74.

Image 72
Contents SAS and Sata HostRAID Controller Copyright Adaptec Customer Support Limited 3-Year Hardware Warranty Regulatory Compliance Statements Contents Getting Started Managing Your Storage Space Using the ARC Utility Safety Information About This Guide What You Need to Know Before You BeginHow to Find More Information What You Need to Know Before You BeginTerminology Used in this Guide Conventions Used in This GuideAbout This Guide l About Your HostRAID Controller HostRAID Controller Features Array Level FeaturesAbout Your HostRAID Controller l About the Adaptec 58300 Controller PCI-XAbout the Adaptec 48300 Controller About the Adaptec 44300 Controller About the Adaptec 1430SA Controller About the Adaptec 1420SA Controller About the Adaptec 1220SA Controller About the Adaptec 1225SA Controller Kit Contents and System Requirements Kit Contents System RequirementsInstalling the HostRAID Controller Disk Drives Installing the HostRAID Controller Before You BeginSelecting Disk Drives Selecting SAS CablesInstalling the HostRAID Controller and Disk Drives l Connecting Disk Drives to SAS HostRAID Controllers Selecting Sata CablesConnecting Directly to the HostRAID Controller Connecting to a BackplaneConnecting Disk Drives to Sata HostRAID Controllers Installing the SAS HostRAID Controller to a SAS ExpanderChecking Your Controller and Devices Setting the Boot Controller Next Steps Getting Started Choosing Installation Options Basic Installation StepsInstalling with an Operating System Choosing a RAID LevelInstalling on an Existing Operating System Creating a Bootable Array Creating an Array Creating an Array with the ACUCreating an Array with Adaptec Storage Manager Making Your Array Bootable Select Express configuration..., then click NextInstalling the Driver and an Operating System Installing with Windows Creating a Driver DiskInstalling with Red Hat Linux Installing with Suse LinuxInstalling with NetWare Installing the Driver on an Existing Operating System Installing on Windows XP or Windows Creating a Driver Disk or an ArrayInstalling on Windows Vista Installing on Red Hat or Suse LinuxInstalling on NetWare Continue with Managing Your Storage Space on Managing Your Storage Space About the Hrconf Command Line Utility Installing Adaptec Storage ManagerAbout Adaptec Storage Manager About the ARC Utility About the Adaptec Flash UtilityWhich Utility Should I Use? Solving Problems Troubleshooting Checklist Recovering from a Disk Drive FailureFailed Disk Drive Protected by a Hot Spare Failed Disk Drive Not Protected by a Hot SpareResetting the Controller Failure in Multiple Arrays SimultaneouslyDisk Drive Failure in a RAID 0 Array Multiple Failures in the Same ArraySolving Problems l Understanding RAID RAID Technology Overview RAID 0 Non-RAID ArraysUnderstanding Drive Segments Stripe-Unit SizeRAID 1 Arrays RAID 10 ArraysSelecting the Best RAID Level Introduction to SAS What is SAS? Terminology Used in This AppendixHow Do SAS Devices Communicate? What’s a Phy?What’s a SAS Port? What’s a SAS Connector? What’s a SAS Address?What do SAS Cables Look Like? How are Disk Drives Identified in SAS?What are the SAS Connection Options? Direct-Attach ConnectionsBackplane Connections SAS Expander ConnectionsHow is SAS Different from Parallel SCSI? SAS DomainParallel Scsi Serial Attached Scsi Using the ARC Utility Introduction to the ARC Utility Running the ARC UtilityCreating and Managing Arrays Creating a New ArrayQuick Init Creating a RAID 0 on new drives Managing Arrays Rebuilding ArraysViewing Array Properties Adding/Deleting Hot Spares Deleting ArraysEnabling/Disabling Write Cache Using SerialSelect Managing Bootable Arrays and DevicesConfiguring Disk Drives Atapi SupportSerialSelect Options DeviceUsing SATASelect PHY ConfigurationFormatting and Verifying Disk Drives SATASelect OptionsLocating Disk Drives Identifying Disk DrivesViewing the Event Log Using the Adaptec Flash Utility for DOSIntroduction Compatibility InformationObtaining the Firmware Running the AFU Creating the Firmware Kit On Floppy DisksRunning the Menu-Based AFU AFU Commands Running the AFU from the Command LineExamples Command Syntax Command SwitchesExample Update Updating Flash Using AFU Command Line \ AFU Verify /CTo update a single HostRAID controller HostRAID Controller LED and I2C Connector Reference Adaptec 58300 Activity LED Connector Specification Adaptec 48300 Activity LED Connector SpecificationAdaptec 44300 Activity LED Connector Specification Adaptec 1430SA Activity LED and I2C Connector SpecificationAdaptec 1420SA Activity LED and I2C Connector Specification LedsumAdaptec 1220SA Activity LED Connector Specification Adaptec 1225SA Activity LED SpecificationSafety Information Electrostatic DischargeESDTechnical Specifications Environmental Specifications DC Power RequirementsCurrent Requirements Glossary Configure Configured arrayConsistency check command BuildFault-tolerant array Disk IDDrive LED EventNative Command Queuing Legacy diskLogical device Low-level formatRAID volume Simple volumeRAID signature RebuildVolume Stripe sizeStriped array TaskIndex ACUSATASelect SerialSelect utilities SATASelect Adaptec, Inc

1430SA, 1225SA, 1420SA, 1220SA, 48300 specifications

Adaptec, a prominent name in the world of storage solutions, offers a diverse array of RAID controller cards aimed at enhancing data storage and management in both consumer and enterprise markets. Among its acclaimed products are the Adaptec 1220SA, 1430SA, 44300, 1225SA, and 1420SA. These cards ensure increased data protection, improved performance, and greater scalability.

The Adaptec 1220SA is a robust SATA RAID controller designed for small to medium-sized businesses. It supports RAID levels 0, 1, 1E, 5, and 10, providing flexibility for users to optimize data redundancy and performance. With the capability of handling up to four SATA drives, it guarantees an efficient and reliable setup while minimizing potential data loss. The controller also features an intuitive web-based management interface, making it easier to administer and configure.

The Adaptec 1430SA extends similar functionality with enhanced features. It is designed to accommodate up to eight SATA drives and supports the latest 3 Gbps SATA technology. This model includes optional battery backup for preserving critical data during unexpected power outages, ensuring that users maintain data integrity and protection at all times.

In the enterprise domain, the Adaptec 44300 shines as a high-performance RAID controller. It offers support for 12 SATA drives, which allows for expansive storage scalability, crucial for data-intensive applications. The advanced RAID features include support for RAID 6, providing dual parity data protection. The controller is built with a powerful processor and memory, allowing for faster data processing and enhanced throughput.

The Adaptec 1225SA is another noteworthy model. Designed for entry-level RAID applications, it offers a balanced combination of performance and reliability. Supporting up to four SATA drives, the 1225SA is particularly well-suited for environments where uptime is critical, delivering functionalities such as hot-swapping. This feature allows users to replace failed drives without shutting down the system, significantly reducing downtime.

Lastly, the Adaptec 1420SA caters to users who require a cost-effective but reliable storage solution. With support for RAID 0, 1, and JBOD, it is a versatile option for enthusiasts and small businesses. The controller can manage up to two SATA drives, making it ideal for basic applications where simplicity and efficiency are paramount.

Collectively, these Adaptec controllers showcase cutting-edge RAID technology and storage management features, reinforcing their position as reliable options for users ranging from home users to enterprise-level organizations seeking optimal data storage solutions.