Rose electronic MAN-VR2 manual Safety and EMC Regulatory Statements, Grounding, Servicing

Page 53

Safety and EMC Regulatory Statements

Safety Information

Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product.

WARNING	A WARNING in the manual denotes a hazard that
can cause injury or death.
CAUTION	A CAUTION in the manual denotes a hazard that can
damage equipment.

Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps.

Grounding

These are Safety Class I products and have protective earthing terminals. There must be an un-interruptible safety earth ground from the main power source to the product’s input wiring terminals, power cord, or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored.

Servicing

There are no user-serviceable parts inside these products. Only service-trained personnel must perform any servicing, maintenance, or repair.

The user may adjust only items mentioned in this manual

Vista Remote 2 Installation and Operations Manual		47

Image 53

Contents Vista Remote Page Limited Warranty FCC / IC STATEMENTS, EU Declaration of Conformity Table of Contents Figures System Introduction IntroductionPackage contents FeaturesRose Electronics web site Product RegistrationSystem Overview OverviewVista Remote 2 Models Vista Remote 2 ModelsConnecting the KVM station InstallationVista Remote 2 Installation Connecting to the network Connecting the ComputersConfiguring the Vista Remote 2 IP Input module Unit ConfigurationHardware Admin passwordFirmware Keyboard LayoutConfiguring the Network Network ConfigurationMAC address Use DHCP/IP address/Net Mask/Gateway/VNC port/HTTP PortSecure Key calculation Control menu Logoff Restore mouse functionsConfiguration Connecting RemotelyAccess mode HostRemote Configuration User Accounts User AccountsUnit Configuration Unit Advanced Configuration Behavior for admin connections when limit reached Single Mouse Mode Mouse SwitchUpgrade Firmware Reset UnitTime and Date Configuration Time and Date ConfigurationMAC address Network ConfigurationUse Dhcp IP AddressIP Access Control Host ConfigurationIP Gateway VNC PortName Logging and StatusUsers Hotkey / KVM PortTo copy and paste the log KVM Switch Module OSD KVM Switch Module ConfigurationChange computer names Change the computer namesAppearance options Configure appearanceForeground/Background color Name x or y positionName font Name fadeout timeScreen saver type Screen saver timeAccess password Configure securityAccess time Configure mouse typeConfigure Keyboard Configure keyboard typeScan time Configure miscellaneousExit SaveRemote System Operation Connecting using a web browserOperation VNC Viewer Toolbar Viewer encryption settingsControls Tab Setting the Threshold manually Video SettingsVirtual Media InfoHost Tab Vista Remote 2 Installation and Operations Manual Command Key Sequence Description HotKey Command Keyboard CommandsKeyboard commands Keyboard command description Reset computer mouse type NT and WIN 2K systems only ResetKeep command Mode commandTroubleshooting TroubleshootingWhen logging on using VNC viewer, I cannot enter a username Remote network users are unable to contact the unitCan’t switch computers from keyboard Computer does not boot, keyboard or mouse error receivedMouse driver does not load Wrong or missing characters from those typedVideo fuzzy Lower resolution OK, but can’t enter high resolution modeVideo not synchronized or wrong color On-screen display not synchronizedTechnical Support Maintenance and RepairSafety SafetyServicing Safety and EMC Regulatory StatementsGrounding Appendix B Part Numbers Appendix a General specificationsAppendices Appendix C RackMount Setting IP access control Appendix D IP Access ControlNetwork/Address Single locationsMask Vista Remote 2 Installation and Operations ManualAddress ranges To reorder access control entries AccessTo edit/remove access control entries Appendix E VNC Viewer connection optionsAuto select Color/EncodingPreferred encoding Color levelInputs ScalingMisc Identities Defaults Reload Configuration File Save AsDefaults Save Load / SaveAppendix E VNC viewer window options Encoding and color level Appendix F Browser viewer optionsSecurity Appendix G Supported video modes Typematic Rate Typematic DelayAppendix H Typematic Rate Appendix I Hot Key Codes Vista Remote 2 Installation and Operations Manual Page Stancliff Road Phone 281 Houston, Texas