PowerDsine PD-6006, PD-6012, PD-6024 manual Connectors, Port Status Indications

Page 10

 

 

 

 

 

 

 

 

PD-6006/12/24

 

 

 

 

 

 

Table 2-2: Port Status Indications

 

 

 

 

 

 

 

 

 

 

 

 

 

Port LED Color

 

 

Port Load Conditions

 

 

Port Voltage

 

 

 

Off

 

 

Non-active load or

 

Power to the port is disconnected.No

 

 

 

 

 

unplugged port.

 

 

DC voltage present on spare pairs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Active load is plugged in

 

 

Continuous nominal DC voltage is

 

 

 

Green

 

 

and complies with

 

 

present on the spare pairs.

 

 

 

 

 

 

normal load conditions.

 

 

 

 

 

 

 

 

 

Overload conditions; or

 

 

Power to the port is disconnected.

 

 

 

Orange

 

 

short; or forced external

 

 

No DC voltage is present on the

 

 

 

 

 

voltage feed (constant

 

 

spare pairs.

 

 

 

 

 

 

DC) into the port.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transitional mode in

 

 

Power to the port is disconnected.

 

 

 

Green blinking

 

 

which load detection is in

 

 

No DC voltage is present on the

 

 

 

 

 

 

process or discharged

 

 

spare pairs.

 

 

 

 

 

 

capacitor in the PD.

 

 

 

 

 

 

 

 

 

Total aggregated power

 

 

Power to the port is disconnected.

 

 

 

Orange blinking

 

 

exceeds pre-defined

 

 

No DC voltage is present on the

 

 

 

 

 

 

power budget.

 

 

spare pairs.

 

 

 

 

 

 

 

 

 

 

 

2.4Connectors

The front panel of the Midspan includes a Console port (DB-9 connector). The user may connect a terminal and perform software loading, via this connector, using a standard null modem cable. The console port is set to 19,200-baud, 8 data bits, no parity and 1 stop bit. Pin connections for this connector are:

Pin 2 is Receive (RXD) Pin 5 is Ground

Pin 3 is Transmit (TXD) Pins 1 and 6 are shorted

Each data port is configured

 

 

 

 

 

 

 

 

 

as shown in Figure 2-2., as

Ethernet

 

RJ-IN

 

RJ-OUT

 

 

PD

data route-thru ports for all

Switch

 

 

Bus

 

 

 

 

 

 

 

 

 

1

Data

1

1

Data

1

 

data pins (pins 1, 2, 3 and

 

 

 

2

Data

2

Power

2

Data

2

 

6).Be certain to use

RJ-45

3

Data

3

3

Data

3

RJ-45

Category 5 or higher cabling,

4

 

4

 

4

DC +

4

 

5

 

5

 

5

DC +

5

 

as shown in the figure.

 

6

Data

6

 

6

Data

6

 

 

 

7

 

7

 

7

DC -

7

 

Figure 2-2: Connecting to

 

8

 

8

 

8

DC -

8

 

 

 

 

 

 

 

 

 

 

the Midspan

 

 

 

Midspan Channel

 

 

 

Power over LAN Solutions

10

 

 

 

 

Cat. No.: 06-6800-056

Image 10
Contents Power over LAN Midspans Disclaimer Contents Model Numbers Definition Verifying Kit ContentsSafety Standard Approvals Electrical Compatibility ApprovalsSafety Information General GuidelinesPower Cord Disconnecting the power cord from the outletAbout the Power over LAN Midspan Power ManagementPrimary Power Indicators IndicatorsData & Power Output Ports 10/100BASE-TX Ports DefinitionPower Status Indications Port IndicationsConnectors Port Status IndicationsBackground Information Installing the Power over LAN MidspanRack Mounting Brackets Powering up Connecting Ethernet CablesConnecting Power Cables TroubleshootingTroubleshooting Guide Troubleshooting StepsSymptom Corrective Steps Parameter PD-6006 PD-6012 PD-6024Remote Power Management Management DeploymentPart Number Release