SUPER MICRO Computer X7DCL-i, X7DCL-3 user manual IDE Connector, Simlc Ipmi Slot, IDE Simlc

Page 52

X7DCL-3/X7DCL-i User's Manual

IDE Connector

IDE Drive Connector

Pin Definitions

An IDE Connector is located at JIDE1 on the motherboard. This motherboard uses the ITE IT8213F Controller. An IDE Driver is required for the IDE drive to function properly. See the table on the right for pin definitions.

SIMLC IPMI Slot

ALow Profile SIMLC IPMI Slot is located on the motherboard. Refer to the layout below for the IPMI Slot location.

Pin# Definition

1Reset IDE

3Host Data 7

5Host Data 6

7Host Data 5

9Host Data 4

11Host Data 3

13Host Data 2

15Host Data 1

17Host Data 0

19Ground

21DRQ3

23I/O Write

25I/O Read

27IOCHRDY

29DACK3

31IRQ14

33Addr1

35Addr0

37Chip Select 0

39Activity

Pin # Definition

2 Ground

4Host Data 8

6Host Data 9

8Host Data 10

10Host Data 11

12Host Data 12

14Host Data 13

16Host Data 14

18Host Data 15

20Key

22Ground

24Ground

26Ground

28BALE

30Ground

32IOCS16

34Ground

36Addr2

38Chip Select 1

40Ground

USB0/1 KB/MS

JPWF1

JAR


8-Pin PWR			24-Pin		PWR

SMB_PS

Fan 1

CPU1 VRM OH LED

LED5

A.IDE

B.SIMLC

		DIMM2A		CPU1
COM1				CPU1
COM1		DIMM1A
		DIMM2B
		DIMM1B
		DIMM2C
VGA		DIMM1C
		X7DCL-3/i
LAN1
LAN2	JPL2			CPU2
LAN2	LAN
	CTRL	Intel	5100
	FAN5	Intel	5100
	FAN5	North Bridge
	FAN6	North Bridge
	FAN6
	I-Button			LED6	Fan 2
				LED6	Fan 2
	LAN		JP2	CPU2 VRM OH LED
	CTRL		JP1
	Slot6 PCI-E x8	SP1			Fan 3
		Buzzer

JPL1	JI2C2	JI2C1		Intel	GPIO0-SATA	GPIO1-SATA
			Slot5 PCI-E x8	ICH9R
				ICH9R
				South Bridge

VGA	Slot4 PCI-E x4(in x8 slot)	SATA5	SATA4	SATA3	SATA2
VGA
CTRL		JBT1
JPG1	Slot3 PCI 33MHz	BIOS		JD1
		Battery

	S I/O		Slot2 PCI 33MHz	ITE	SAS-GPIO1
		JWD1		CTRL
			JWOL1		SAS-GPIO0

			Slot1 PCIB33MHz	LED4	JPA2
	JWOR1	JKEY1		LED4	USB2/3	SAS0	SAS1	SAS2	SAS3
	JWOR1	JKEY1			USB2/3	SAS0	SAS1	SAS2	SAS3
				System Status LED	USB4/5
COM2				System Status LED	USB4/5
COM2
			SIMLC		BPI2C

			PWR LED		CTRL
			LED3		CTRL
SATA1	SATA0		JPA1		FP
			LED1
LSI					Floppy
SAS					IDE
CTRL					IDE
SAS4	SAS5	SAS6	SAS7	JL1
					Fan 4

A

2-32

Image 52

Contents Super Page Manual Organization About This ManualConventions Used in the Manual Table of Contents Table of Contents Troubleshooting BiosIntroduction Running Setup Advanced SetupChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificX7DCL-3/X7DCL-i Image X7DCL-3/X7DCL-i Motherboard Layout Not drawn to scaleJumper Description Default Setting LED Indicator DescriptionQuick Reference X7DCL-3/X7DCL-i JPA1 NoteMotherboard Features MemoryChipset Expansion SlotsAcpi Features DimensionsOnboard I/O OtherBlock Diagram of the Intel 5100 Chipset MCH5100 Memory Controller Hub MCH Chipset and Processor Features OverviewNinth Generation I/O Controller Hub ICH9 Special Features PC Health MonitoringAcpi Features Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism External Modem Ring-OnPower Supply Super I/OPage Page Static-Sensitive Devices PrecautionsUnpacking Processor and Heatsink Fan Installation Installing the LGA771 ProcessorLoading the Processor into the Socket Installing the Heatsink To Remove the HeatsinkDimm Installation Installing DIMMsMounting the Motherboard in the Chassis Memory Support Dimm 1A Dimm 2ADimm 1A Dimm 1B Dimm 2A Dimm 2B Dimm 1A Dimm 1B Dimm 1C Dimm 2A Dimm 2B Dimm 2CTo Remove Installing and Removing DIMMsPossible System Memory Allocation & Availability Control Panel Connectors/IO Ports Back Panel Connectors/IO PortsJF1 Header Pins Power LEDPower Button Front Control PanelPower LED Front Control Panel Pin DefinitionsNMI Button NMI PWR LEDNIC1/NIC2 LED Indicators HDD LED NIC1 LED NIC2 LEDOverheat/Fan Fail LED OH Power Fail LEDOH/Fan Fail LED B. PWR Supply Fail Reset Button Power ButtonReset Button PWR Button Reset Button Pin Definitions JF1Connecting Cables ATX Power ConnectorProcessor Power Connector Required ConnectionUniversal Serial Bus USB Backpanel USB 0/1 Front Panel USB 2/3 Front Panel USB 4/5Back Panel USB 0/1 Pin Definitions Front Panel USB Pin Definitions USB2/3/4/5Fan Headers Chassis IntrusionFan Chassis Intrusion Fan Header Pin Definitions Fan1-6ATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsKeyboard/Mouse COM1 COM2Wake-On-Ring Wake-On-LANWOR WOL Wake-On-Ring Pin DefinitionsPower LED/Speaker Speaker ConnectorGlan 1/2 Giga-bit Ethernet Ports GLAN1 GLAN2Alarm Reset PWR Supply Failure/PWR Fault DetectAlarm Reset PWR FaultVGA Connector Gpio HeadersVGA J7 SATAGPIO#0 J8 SATAGPIO#1 J9 SASGPIO#0 J10 SASGPIO#1Power SMB I2C Connector BP PWR SMB I2C ConnectorPWR SMB Backplane PWR SMBKeylock KeylockKeylock Pin Definitions Jumper Settings Glan Enable/DisableGlan Port1 Enable B. Glan Port2 Enable Glan Enable Jumper SettingsWatch Dog Enable/Disable Clear Cmos Watch Dog EnableWatch Dog Jumper Settings Cmos ClearVGA Enable/Disable VGA Enable/Disable Jumper SettingsI2C Bus to PCI/PCI-Exp. Slots JPI2C1 C. JPI2C2SAS Enable/Disable Software RAID EnableSAS Enabled Software RAID Enable SAS Enable/Disable Jumper SettingsOnboard LED Indicators Onboard Power LED LED3Glan LEDs LEDCpuvrm Overheating LED Indicators LED5/LED6 System Status LED LED4LED4 System Status LED LED5 CPU1VRM OH LED LED6 CPU2VRM OH LEDSAS LED Indicator LED1 LED1 SAS LEDFloppy Drive, Simlc Ipmi and Hard Disk Drive Connections Floppy ConnectorFloppy Disk Drive Simlc Ipmi Slot IDE ConnectorIDE Simlc Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup ConfigurationTechnical Support Procedures Memory ErrorsFrequently Asked Questions Returning Merchandise for Service Question Whats on the CD that came with my motherboard?System Bios How To Change the Configuration DataStarting the Setup Utility IntroductionMain Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesLBA Mode Control SATA Port 1 ~ Sata Port 6, Ext. Primary Master/SlaveType Multi-Sector TransfersTransfer Mode Ultra DMA ModeNative Mode Operation Sata Controller ModeSystem Memory Sata Ahci EnableExtended Memory Advanced Setup Power Button Behavior Power Loss ControlMemory Cache Cache System Bios Area Cache Video Bios AreaCache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationPCI Configuration Onboard GLAN-1/Onboard GLAN-2 Gigabit- LAN Oprom ConfigureOnboard Storage Oprom Configure Reset Configuration DataClock Spectrum Feature Crystal Beach Configure EnableSerr Signal Condition Advanced Chipset ControlEnable Multi-Media Timer Demand ScrubbingPatrol Scrubbing Route Port 80h Cycles toC1 Enhanced Mode Available if supported by the CPU Machine Checking Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Core-Multi-Processing Available if supported by the CPUI/O Device Configuration CPU Cache ControlIntel Eist Support Available if supported by the CPU KBC Clock InputBase I/O Address InterruptSerial Port B ModeEvent Logging ECC Event LoggingMark DMI Events as Read Clear All DMI Event LogsCPU1 Temperature/CPU2 Temperature CPU Overheat AlarmHardware Monitor System Temperature Fan Speed Control Modes Fan1-Fan6 SpeedsVoltage Monitoring System Event Logging Clear System Event LoggingExisting Event Log Number Event Log ControlSystem Event Log/System Event Log List Mode Bios Post Watch DogOS Boot Watch Dog Timer for Loading OS MinutesIPMI LAN Configuration Realtime Sensor DataSupervisor Password Is User Password IsSet Supervisor Password Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B Installing the Windows OS Page Installing other Drivers and the OS Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control