6 3-Wire Conduit Installation, Note Aluminum Wiring | GE 49-8779

6 3-Wire Conduit Installation

Customer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety Information

Installation of the range.

Read these instructions completely and carefully.

6 3-Wire Conduit Installation

Remove the 3 screws from the connector block. Insert bare wires between the connector block terminals and movable nuts. Tighten screws securely. Do not remove ground strap connection.

WARNING: Connector block is approved for copper wire connection only. If aluminum wire is used, see note below.

NOTE: ALUMINUM WIRING

a Do not connect aluminum wire to the connector block.

Use copper building wire rated for the correct amperage and voltage to make 3 (three) 3″ copper jumper wires. Connect wire as per Step 6 or 7 depending on number of wires.

b Splice copper wires to aluminum wiring using special connector terminals designed and UL-approved for joining copper to aluminum and follow the connector manufacturer’s recommended procedure closely.

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes.

Screw
Connector block	Bare wire tips
Connector block terminal
Bare wire
Movable nut
Flexible cable
Bracket	Conduit
	Conduit

50

Image 50

GE 49-8779, 164D3333P033 manual 6 3-Wire Conduit Installation, Note Aluminum Wiring, Installation of the range

Contents

Owner’s Manual GE AppliancesGE Answer Center JBP90 JBP95 Write the model and serial numbers here # # Staple sales slip or cancelled check hereCongratulations You Are Now Part of the GE Family drawer If You Need Service GE & You A Service PartnershipTroubleshooting Tips Safety Information or using a ventilation fan or hood IMPORTANT SAFETY NOTICEIMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING WARNING ANTI-TIP DEVICE SAFETY PRECAUTIONS Safety Information Operating Safety Information WHEN COOKING PORK… Safety Information Operating Instructions Installation OVEN SELF-CLEANING OVEN Instructions Safety Information HALOGEN/RADIANT SURFACE UNITS Always turn the surface units off before removing cookware Cleaning the glass cooktop section Customer ServiceInstructions Safety Information HALOGEN/RADIANT SURFACE UNITS How to Set Using the surface unitsSafety Indicator Lights Differences Between Halogen and Radiant Units Instructions Operating Instructions Safety InformationDual Surface Unit Switch Temperature Limiter Aluminum Selecting types of cookwareStainless Steel Copper Bottom STOP TIME Using the oven controlsTIMER ON/OFF CLOCK BROIL HI/LO Pad Oven Control SettingsAUTO SELF CLEAN CONV. ROAST Pad D C B A Using the ovenSafety Information Operating Instructions How to Set the Oven for Broiling Preheating and Pan PlacementSafety Information Operating Instructions Installation Instructions Aluminum Foil First Side Broiling guideShelf Food To Set the Timer Using the clock and timerInstallation To Reset the Timer Using the timed baking and roasting features How to Set an Immediate Start and Automatic Stop How to Set a Delay Start and Automatic Stop Make sure the oven clock shows the correct time of day Information Using the probeInstructions Safety Do not store the probe in the oven Insert the probe into the meat How to set the oven for roasting when using the probeYou can use the timer even though you cannot use timed oven operations Convection Bake Using the convection ovenThe convection oven fan shuts off when the oven door is opened Convection Roast Paper and Plastic Adapting Recipes…Cookware for Convection Cooking Metal and Glass Troubleshooting How to Set the Oven for Convection Baking or RoastingMulti-Shelf Baking How to Set the Oven for Convection Roasting when Using the Probe Beef Convection roasting guideMeats Pork Using the timed features for convection baking Using the timed features for convection baking Press the CLEAR/OFF pad to clear the display if To Adjust the Thermostat Adjust the oven thermostat-Do it yourself Using the self-cleaning oven Before a Clean Cycle How to Set the Oven for Cleaning Press the AUTO SELF CLEAN pad How to Delay the Start of Cleaning After a Clean Cycle tipping of the range and cause injury Care and cleaning of the rangeor any reason, be sure the anti-tip device is Control Panel and Knobs To clean the outside of the door Lift-Off Oven DoorTo clean the inside of the door Do not lift the door by the handle the main fuse or circuit breaker panel Oven Light ReplacementOven Heating Elements disconnect the electrical power to the range at How to Remove the Storage Drawer or Kick Panel to Clean Under the RangeBroiler Pan & Grid To remove the storage drawer To remove Cooktop Surface LightSure Grip Handle To replace For heavy, burned-on soil Cleaning the glass cooktopDaily Cleaning National Parts Center Special Care BEFORE BEGINNING INSTALLATION Installation of the rangeInstallation Instructions for future use Before You Begin Not less than the width 1 Prepare the Openinginstall in either rear corner 30 ″ When moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows Flooring Under the Range2 Prepare for Electrical Connection 3 Power Cord Strain Relief Installation Do NOT remove ground strap connection 4 3-Wire Power Cord InstallationConnector block Neutral terminal Ground strap Power cord After 5 4-Wire Power Cord InstallationBefore a Do not connect aluminum wire to the connector block 6 3-Wire Conduit InstallationNOTE ALUMINUM WIRING 7 4-Wire Conduit Installation 10 Final Check 8 Anti-Tip Bracket Installation9 Leveling the Range Problem Before you call for service…Troubleshooting Tips Customer Service See the Using the the Broiling guide See the Adjust the ovenSee the Broiling guide See the Using the clock and timer section Excessive smoking Oven not cleanafter a clean cycle Oven door will Problem We Will Replace, At No Charge To You GE Electric Range WarrantyTroubleshooting Tips What GE Will Not Cover TDD 800-TDD-GEAC Service Telephone NumbersIn-Home Repair Service 800-GE-CARES Special Needs Service