SUPER MICRO Computer AOC-SOZCR1 manual Chapter Technical Speciﬁcations and Software Installation

Page 7

Chapter 2: Technical Speciﬁ cations and Installation

Chapter 2

Technical Speciﬁcations and Software

Installation

2.1 AOC-LPZCR1 Card Layout and Jumper Locations

2.1.1AOC-LPZCR1 Card Layout and Jumper Locations

Front view (AOC-LPZCR1)

2.5”

		Buzzer	Connector

Cache

Cache

Cache

7.0”

5V LED DS14	DS13	3V LED	Flash Firmware			AOC-LPZCR1 Rev. 1.01
5V LED DS14	DS13	3V LED	Flash Firmware	J6	J2 Act.	J1 I2C
							J7	SAS
						CPLD	J5	SATA2
						CPLD	J3	SCSI
							J3	SCSI

I/O Processor
Flash EPROM	NVS RAM

Rear view

DS 8

DS 7

DS 6

DS 5

DS 4

DS12 DS11

DS10

Diag.LED Diag.LED

Flash EPROM

SRAM

Cache

Cache

Flash EPROM

2-1

Image 7

Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents AOC-SOZCR1 Series the Terminator Socket Dimm ZCR Card IntroductionAOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID Card Key RAID FeaturesOperating Systems supported Management supportEurope HeadquartersAsia-Paciﬁc AOC-LPZCR1 Card Layout and Jumper Locations Chapter Technical Speciﬁcations and Software InstallationJumper Description Jumper and Connector Descriptions *AOC-LPZCR1Description I2C Cable Connection Connectors and LED Indicators *AOC-LPZCR1Activity LED Indicator Buzzer ConnectorFront view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsRear view AOC-SOZCR1 2C cable Connection Connector and Header Descriptions *AOC-SOZCR1SMB Connector and Pin Deﬁnitions *AOC-SOZCR1 SMB I 2CSee Note 1 below Intelligent Interface Management SAF-TEGeneral Safety Guidelines ESD Safety GuidelinesFor the Red Hat/SuSE Operating System Creating the Driver Floppy DiskAdding the Driver into an Existing System For the Windows 32-bit Operating SystemFor the Red Hat Operating System Installing the Driver into a New SystemFor the SuSE Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Chapter RAID Conﬁguration Conﬁguring Jumper SettingsSAS, Sata and Scsi settings Using Adaptecs RAID Conﬁguration UtilityTo Use the Adaptec RAID Conﬁguration Utility RAID Conﬁguration Utility Main Menu Using the Array Conﬁguration UtilityArray Conﬁguration Utility Main Menu To Create ArraysPage To assign properties to the new array To Manage ArraysTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive To initialize Disk drives Initializing Disk DrivesPage Page Rebuilding Arrays To Rebuild an array To Rescan Disk drivesTo Secure Erase Drives Page Using the Controller Conﬁguration Utility Using Adaptecs SCSISelect UtilityUsing the Scsi Conﬁguration Utility Page Page Using the Sata Conﬁguration Utility Using Adaptecs SATASelect UtilityTo Use the SATASelect Utility To Use the SerialSelect Utility Using Adaptecs Serial Select UtilityUsing Physical Conﬁguration Utility To Use Disk Utilities *for Scsi only Using Disk UtilitiesPage To Format a Disk Drive To Use Disk Utilities *for Sata and SAS onlyTo Verify Disk Media To Exit the Adaptec RAID Conﬁguration UtilityChapter Troubleshooting Contacting Supermicros Technical Support