SUPER MICRO Computer AOC-LPZCR1 manual Connector and Header Descriptions *AOC-SOZCR1, SMB I 2C

Page 11

Chapter 2: Technical Speciﬁ cations and Installation

2.2.2 Connector and Header Descriptions (*AOC-SOZCR1)

Connector		Description
J1		Systerm Management Bus (I2C) (*See Page 2-2 for
		I2C cable connection.)
J2		SCSI Mode (On: Enable)
J3		Serial ATA (SATA2) Mode (On: Enable)
J4		SAS Mode (On: Enable)
J6		Flash Firmware (On: Flashing Firmware.)

2.2.3 SMB Connector and Pin Deﬁnitions (*AOC-SOZCR1)

SMB (I2C)
SMB (I2C)				SMB (I2C)
				SMB (I2C)
A System Management Bus header is			Pin Definitions (J1)
located at J1. Connect the I2C cable
located at J1. Connect the I2C cable			Pin	Definition
here to utilize SMB on your add-on			Number	Definition
here to utilize SMB on your add-on			1		Data
card (*See below). See the table on			2	Ground
card (*See below). See the table on			3		Clock
			3		Clock
the right for pin deﬁ nitions.

I2C cable Connection	3-Pin Connector (J1) on				3-PinConnector on
I2C cable Connection	3-Pin Connector (J1) on					the cable
			the SOZCR1			the cable

1.The I2C Cable has a 3-pin connec- tor on one end, and a 4-pin connector on the other end.

2.Connect the 3-pin connector of the cable to the 3-pin I2C Connector (J1) on the AOC-SOZCR1 card.

3.Connect the 4-pin connector of the cable to the 4-pin I2C Connector on the backplane as shown on the right.

4-Pin I2C Connector	4-Pin Connector on
on the Backplane	the cable

*Note 1: Refer to the layout on Page 2-4 for the locations of the Connectors and LED Indicators.

2-5

Image 11

Contents

Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents AOC-SOZCR1 Series the Terminator Socket Dimm ZCR Card IntroductionAOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID Card Key RAID FeaturesOperating Systems supported Management supportAsia-Paciﬁc HeadquartersEurope AOC-LPZCR1 Card Layout and Jumper Locations Chapter Technical Speciﬁcations and Software Installation Description Jumper and Connector Descriptions *AOC-LPZCR1 Jumper Description I2C Cable Connection Connectors and LED Indicators *AOC-LPZCR1Activity LED Indicator Buzzer ConnectorRear view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsFront view AOC-SOZCR1 2C cable Connection Connector and Header Descriptions *AOC-SOZCR1SMB Connector and Pin Deﬁnitions *AOC-SOZCR1 SMB I 2CSee Note 1 below Intelligent Interface Management SAF-TEGeneral Safety Guidelines ESD Safety GuidelinesFor the Red Hat/SuSE Operating System Creating the Driver Floppy DiskAdding the Driver into an Existing System For the Windows 32-bit Operating SystemFor the SuSE Operating System Installing the Driver into a New SystemFor the Red Hat Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Chapter RAID Conﬁguration Conﬁguring Jumper SettingsTo Use the Adaptec RAID Conﬁguration Utility Using Adaptecs RAID Conﬁguration UtilitySAS, Sata and Scsi settings RAID Conﬁguration Utility Main Menu Using the Array Conﬁguration UtilityArray Conﬁguration Utility Main Menu To Create ArraysPage To assign properties to the new array To Manage ArraysTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive To initialize Disk drives Initializing Disk DrivesPage Page Rebuilding Arrays To Rebuild an array To Rescan Disk drivesTo Secure Erase Drives Page Using the Controller Conﬁguration Utility Using Adaptecs SCSISelect UtilityUsing the Scsi Conﬁguration Utility Page Page To Use the SATASelect Utility Using Adaptecs SATASelect UtilityUsing the Sata Conﬁguration Utility To Use the SerialSelect Utility Using Adaptecs Serial Select UtilityUsing Physical Conﬁguration Utility To Use Disk Utilities *for Scsi only Using Disk UtilitiesPage To Format a Disk Drive To Use Disk Utilities *for Sata and SAS onlyTo Verify Disk Media To Exit the Adaptec RAID Conﬁguration UtilityChapter Troubleshooting Contacting Supermicros Technical Support