SUPER MICRO Computer AOC-SOZCR1, AOC-LPZCR1 manual Operating Systems supported, Management support

Page 5

Chapter 1: Introduction

Supports Marvell's Hercules II 88SX6081 (8-port)/88SX6041 (4-port) Host Con- troller

Supports Adaptec's AIC-7901/-7902 Ultra 320 SCSI Controller and AIC-9410 SAS Controller

RAID 0, RAID 1, RAID 5, RAID 10, RAID 50* and JBOD supported (*See Note 1 Below.)

(2) The AOC-LPZCR1 Series: (-Low Profile Skyhawk ZCR RAID Card)

Low profi le Form Factor (2.5" H x 6.6" W)

Intel's IOP321 I/O Processor (Verde) @ 400MHz built-in

64 MB onboard ECC DDR memory

1 amp@ 3.3V

RAID 0, RAID 1, RAID 5, RAID 10, RAID 50* and JBOD supported (*See Note 1 Below.)

(a) SAS (-based on the Adaptec AIC-9410 Host Controller)

Supports Adaptec's AIC-9410 SAS Host Controller

Supports PCI-X up to 100 MHz in the green slot (*See Note 2)

(b)SATA (-based on the Marvell Hercules II Controller)

Supports Marvell's Hercules II 88SX6081 (8-port) or 88SX6041 (4-port) Host Controller

Supports PCI-X slot up to 100MHz in the green slot (*See Note 2)

(c)SCSI (-based on the Adaptec AIC-7901 or AIC-7902Ultra 320 SCSI Controller)

Supports Adaptec's AIC-7901/-7902 Ultra 320 SCSI Controller

Supports PCI-X up to 100 MHz in the green slot (*See Note 2)

Operating Systems supported

*Windows 2000, Windows XP, and Windows 2003

*Linux: SuSE 9.0, SuSE 9.1, SuSE 9.2, Red Hat 3.0 and Red Hat 4.0

*Upgradable in the future.

Management support

*Adaptec's Storage Manager

*Adaptec Flash Utility

*Adaptec RAID Confi guration Utility

*SAF-TE (*SCSI and SATA only)

Key RAID Features

*RAID detection, confi guration, deletion, addition, and error detection

*Background initialization

*Hot-spare disk drive support for easy replacement

*Hot-spare disk drive support with automatic rebuild

(*Notes:

Note 1:

RAID 50 is available for SAS only.

 

Note 2:

Please install the ZCR card in the green slot.)

 

 

 

1-5

Image 5
Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents AOC-SOZCR1 Series the Terminator Socket Dimm ZCR Card IntroductionOperating Systems supported Key RAID FeaturesManagement support AOC-LPZCR1 Series -Low Profile Skyhawk ZCR RAID CardAsia-Pacific HeadquartersEurope AOC-LPZCR1 Card Layout and Jumper Locations Chapter Technical Specifications and Software InstallationDescription Jumper and Connector Descriptions *AOC-LPZCR1Jumper Description Activity LED Indicator Connectors and LED Indicators *AOC-LPZCR1Buzzer Connector I2C Cable ConnectionRear view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsFront view AOC-SOZCR1 SMB Connector and Pin Definitions *AOC-SOZCR1 Connector and Header Descriptions *AOC-SOZCR1SMB I 2C 2C cable ConnectionSee Note 1 below Intelligent Interface Management SAF-TEGeneral Safety Guidelines ESD Safety GuidelinesAdding the Driver into an Existing System Creating the Driver Floppy DiskFor the Windows 32-bit Operating System For the Red Hat/SuSE Operating SystemFor the SuSE Operating System Installing the Driver into a New SystemFor the Red Hat Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Chapter RAID Configuration Configuring Jumper SettingsTo Use the Adaptec RAID Configuration Utility Using Adaptecs RAID Configuration UtilitySAS, Sata and Scsi settings RAID Configuration Utility Main Menu Using the Array Configuration UtilityArray Configuration Utility Main Menu To Create ArraysPage To assign properties to the new array To Manage ArraysTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive To initialize Disk drives Initializing Disk DrivesPage Page Rebuilding Arrays To Rebuild an array To Rescan Disk drivesTo Secure Erase Drives Page Using the Controller Configuration Utility Using Adaptecs SCSISelect UtilityUsing the Scsi Configuration Utility Page Page To Use the SATASelect Utility Using Adaptecs SATASelect UtilityUsing the Sata Configuration Utility To Use the SerialSelect Utility Using Adaptecs Serial Select UtilityUsing Physical Configuration Utility To Use Disk Utilities *for Scsi only Using Disk UtilitiesPage To Format a Disk Drive To Use Disk Utilities *for Sata and SAS onlyTo Verify Disk Media To Exit the Adaptec RAID Configuration UtilityChapter Troubleshooting Contacting Supermicros Technical Support