SUPER MICRO Computer AOC-SOZCR1 manual Using Disk Utilities, To Use Disk Utilities *for Scsi only

Page 41

Chapter 3: RAID Conﬁ guration

3.3 Using Disk Utilities

The Disk Utilities enable you to format or to verify the integrity of your Hard Drive Disks and to determine if there is any defect. (*Note: Formatting a disk will overwrite data stored in the disk. Please backup your data before format- ting a disk.)

3.3.1 To Use Disk Utilities (*for SCSI only)

(*Note: Please refer to Page 3-1 for SCSI Jumper conﬁ guration before using "Disk Utilities". Please refer to Section 3.3.2 for SAS and SATA Disk Utilities.)

1.Power on your computer. When prompted, press the <Ctrl> and <A> keys simultaneously to enter the RAID Conﬁ guration Utility. From the RAID Conﬁ gu- ration Main Menu, select "Disk Utilities" as shown below:

2.Select "Disk Utilities" and press <Enter>. The Disk Utilities Sub-Menu ap- pears. From the submenu select the Channel (-the disk drive) you wish to format or to scan.

3-25

Image 41

Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents AOC-SOZCR1 Series the Terminator Socket Dimm ZCR Card IntroductionOperating Systems supported Key RAID FeaturesManagement support AOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID CardAsia-Paciﬁc HeadquartersEurope AOC-LPZCR1 Card Layout and Jumper Locations Chapter Technical Speciﬁcations and Software InstallationDescription Jumper and Connector Descriptions *AOC-LPZCR1Jumper Description Activity LED Indicator Connectors and LED Indicators *AOC-LPZCR1Buzzer Connector I2C Cable ConnectionRear view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsFront view AOC-SOZCR1 SMB Connector and Pin Deﬁnitions *AOC-SOZCR1 Connector and Header Descriptions *AOC-SOZCR1SMB I 2C 2C cable ConnectionSee Note 1 below Intelligent Interface Management SAF-TEGeneral Safety Guidelines ESD Safety GuidelinesAdding the Driver into an Existing System Creating the Driver Floppy DiskFor the Windows 32-bit Operating System For the Red Hat/SuSE Operating SystemFor the SuSE Operating System Installing the Driver into a New SystemFor the Red Hat Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Chapter RAID Conﬁguration Conﬁguring Jumper SettingsTo Use the Adaptec RAID Conﬁguration Utility Using Adaptecs RAID Conﬁguration UtilitySAS, Sata and Scsi settings RAID Conﬁguration Utility Main Menu Using the Array Conﬁguration UtilityArray Conﬁguration Utility Main Menu To Create ArraysPage To assign properties to the new array To Manage ArraysTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive To initialize Disk drives Initializing Disk DrivesPage Page Rebuilding Arrays To Rebuild an array To Rescan Disk drivesTo Secure Erase Drives Page Using the Controller Conﬁguration Utility Using Adaptecs SCSISelect UtilityUsing the Scsi Conﬁguration Utility Page Page To Use the SATASelect Utility Using Adaptecs SATASelect UtilityUsing the Sata Conﬁguration Utility To Use the SerialSelect Utility Using Adaptecs Serial Select UtilityUsing Physical Conﬁguration Utility To Use Disk Utilities *for Scsi only Using Disk UtilitiesPage To Format a Disk Drive To Use Disk Utilities *for Sata and SAS onlyTo Verify Disk Media To Exit the Adaptec RAID Conﬁguration UtilityChapter Troubleshooting Contacting Supermicros Technical Support