SUPER MICRO Computer AOC-LPZCR1, AOC-SOZCR1 manual Deleting Arrays

Page 24

AOC-LPZCR1/AOC-SOZCR1 Manual

Deleting Arrays

Warning: To prevent data loss, please back-up your data before deleting arrays. You cannot restore a deleted array.

1.On the Array Conﬁ guration main menu, select "Manage Arrays" and press <Enter> to access the submenu as shown below:

2.From the "List of Arrays" dialogue box (on the right), select the array you wish to delete and press <Del>.

3.The "Array Properties" dialogue box displays. In the "Properties" dialogue box, select <Delete> and press <Enter>. The following warning message will display:

Warning!! Deleting the array will erase all data from the Array. Do you want to continue? (Yes/No):

4.Press <Yes> to delete the array, or press <No> to cancel the selection.

5.Press <Esc> to return to the previous menu.

3-8

Image 24

Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents Introduction AOC-SOZCR1 Series the Terminator Socket Dimm ZCR CardKey RAID Features Operating Systems supportedManagement support AOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID CardHeadquarters EuropeAsia-Paciﬁc Chapter Technical Speciﬁcations and Software Installation AOC-LPZCR1 Card Layout and Jumper LocationsJumper and Connector Descriptions *AOC-LPZCR1 Jumper DescriptionDescription Connectors and LED Indicators *AOC-LPZCR1 Activity LED IndicatorBuzzer Connector I2C Cable ConnectionAOC-SOZCR1 Card Layout and Jumper Locations Front view AOC-SOZCR1Rear view AOC-SOZCR1 Connector and Header Descriptions *AOC-SOZCR1 SMB Connector and Pin Deﬁnitions *AOC-SOZCR1SMB I 2C 2C cable ConnectionIntelligent Interface Management SAF-TE See Note 1 belowESD Safety Guidelines General Safety GuidelinesCreating the Driver Floppy Disk Adding the Driver into an Existing SystemFor the Windows 32-bit Operating System For the Red Hat/SuSE Operating SystemInstalling the Driver into a New System For the Red Hat Operating SystemFor the SuSE Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Conﬁguring Jumper Settings Chapter RAID ConﬁgurationUsing Adaptecs RAID Conﬁguration Utility SAS, Sata and Scsi settingsTo Use the Adaptec RAID Conﬁguration Utility Using the Array Conﬁguration Utility RAID Conﬁguration Utility Main MenuTo Create Arrays Array Conﬁguration Utility Main MenuPage To Manage Arrays To assign properties to the new arrayTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive Initializing Disk Drives To initialize Disk drivesPage Page To Rescan Disk drives Rebuilding Arrays To Rebuild an arrayTo Secure Erase Drives Page Using Adaptecs SCSISelect Utility Using the Controller Conﬁguration UtilityUsing the Scsi Conﬁguration Utility Page Page Using Adaptecs SATASelect Utility Using the Sata Conﬁguration UtilityTo Use the SATASelect Utility Using Adaptecs Serial Select Utility To Use the SerialSelect UtilityUsing Physical Conﬁguration Utility Using Disk Utilities To Use Disk Utilities *for Scsi onlyPage To Use Disk Utilities *for Sata and SAS only To Format a Disk DriveTo Exit the Adaptec RAID Conﬁguration Utility To Verify Disk MediaChapter Troubleshooting Contacting Supermicros Technical Support